Jump to main content

Refrigerator repair in San Antonio, fixed at your place.

Notes from our technicians on the faults we see most in San Antonio refrigerators, from garage units cooking in July to scaled water valves, and how we work through them at your house.

Phones staffed 24/7Three-hour arrival window90-day parts warranty

Diagnosis
The failed part is found before any price
Approval
No work begins without your okay
Hours
Calls answered day and night
Warranty
Parts 90 days · labor 30 days

Book online

Send the basics. A dispatcher calls you back.

  1. 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
  2. 2Pick up when we callWe confirm the address and set a three-hour arrival window.
  3. 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.

Would rather explain it out loud? Call us any hour, any day.

Schedule a repair

Step 1 of 2 · Appliance and area

Step 1 of 2

Appliance and area

Which appliance?

Appliance

Where in the San Antonio area?

Booking costs nothing, and we never ask for a card.

Prefer to call? (210) 939-3313

1–3 hours
Typical time on site
30
Refrigerator faults we fix
37
Brands we service
24/7
Phones answered

Refrigerator problems

What is wrong with your refrigerator?

Pick a symptom for the usual causes and the fix a technician makes.

  • Refrigerator not coolingThe fridge side reads above 40°F, drinks come out cool instead of cold, and leftovers turn faster than they should. The interior light works and the unit may sound normal. That combination points to heat not leaving the box, which can start in the airflow, the defrost system, the condenser or the controls.

    Typical culprits

    • Fan behind the freezer wall has quit, so no cold air crosses into the fridge
    • Defrost fault has let frost bury the evaporator coil
    • Dust and pet hair matted over the condenser coil underneath
    • Condenser fan stuck, so the compressor overheats and shuts off
    • A sensor that reads warm or cold when it shouldn't, misleading the control
    • Refrigerant escaping through a small leak

    How the technician handles it

    First come the thermostat setting, the gasket and the condenser coil with its fan. Next we unscrew the freezer's rear cover to reach the evaporator coil and the fan mounted beside it. Every defrost part and sensor is checked with a meter before we replace anything. We test the sealed system last, after simpler causes have been eliminated.

  • Refrigerator freezer not freezingIce cream turns soft, frozen meat gives a little when you press it, and the freezer feels cool rather than cold. Because the fridge section depends on the same coil, it usually warms up soon after. This is a time-sensitive call if the freezer is full.

    Typical culprits

    • Burned-out defrost heater, so ice keeps growing on the coil
    • Freezer fan dead or its blade locked in ice
    • Worn start relay letting the compressor run only in brief spurts
    • Sealed-system leak that has lowered the refrigerant charge
    • Door kept from sealing by an overstuffed basket or a warped gasket

    How the technician handles it

    The technician checks the door seal and loading, then removes the rear freezer panel to see the coil and fan. A frosted coil means testing the defrost heater, thermostat and control. If the coil is clear and the fan runs, the compressor's start components and the sealed system are next.

  • Refrigerator ice maker not making iceThe bin stays empty or holds a few old, shrunken cubes. Sometimes you hear the valve buzz with no water arriving; sometimes the ice maker is silent. In San Antonio, mineral scale in the fill path is a frequent player.

    Typical culprits

    • Ice plugging the water line where it enters the ice maker at the freezer's rear wall
    • Inlet valve with a dead solenoid or a screen crusted with minerals
    • Freezer running above about 10°F, which keeps the ice mold from reaching harvest temperature
    • Worn-out drive motor or broken gear in the ice maker head
    • Bin-full arm or optical eye stuck in the off position

    How the technician handles it

    We start by confirming the ice maker's switch is on and the freezer temperature is low enough, then check that water reaches the valve and the fill tube is clear. We test the valve electrically and then put the ice maker through a test cycle. Depending on the result we thaw the line, replace the valve or swap the ice maker module.

  • Refrigerator leaking water on the floorA puddle shows up at the front of the fridge, sometimes only after a defrost cycle. The water can come from the defrost drain inside the cabinet or from the supply line and filter. On a slab, water can creep under tile or wood before you see it.

    Typical culprits

    • Defrost drain plugged with debris or iced over
    • Drip pan under the fridge cracked or sitting crooked
    • Weeping supply line or fitting at the water valve
    • Hairline crack in the filter housing or filter head
    • Leveling legs set so the cabinet leans forward and water misses the drain

    How the technician handles it

    If it seems to be coming from the water line, close the supply valve. The technician traces the source by checking the drain pan, the drain path and the water connections, then clears and heats the drain, replaces the cracked part or remakes the fitting. We also check the leveling so the cabinet tips slightly back.

  • Fridge water dispenser not workingYou press the paddle and get nothing, a trickle, or a sputter of air. The ice maker may still work, which narrows it down. Hard water and frozen door lines are both common reasons here.

    Typical culprits

    • Ice blocking the water tube that runs through the door
    • Failed dispenser coil on the two-way water valve
    • Dispenser paddle switch or control not energizing the valve
    • Filter loose in its housing, or the bypass cap left out
    • Shutoff under the sink half-closed, or a saddle tap crusted shut

    How the technician handles it

    We measure water pressure at the valve, test both the valve and the switch, and check the door line for ice. A frozen line is thawed and the cause fixed, usually a freezer set too cold or a leaking gasket. Scaled valves and failed switches are replaced.

  • Refrigerator making a loud noiseGrinding, chirping, rattling or a new buzz that was not there last month. Some sounds are normal, such as water trickling during defrost or the click of a relay. A noise that is rhythmic or scraping usually means a fan or a loose part.

    Typical culprits

    • Ice buildup catching the freezer fan blade
    • Dry, worn bearings in the condenser fan motor
    • Compressor shaking against the frame on tired rubber mounts
    • Loose drip pan or tubing buzzing underneath
    • Auger or dispenser motor in the ice system grinding

    How the technician handles it

    The technician narrows the sound to the freezer, the back of the cabinet or the door. Fan motors with worn bearings are replaced, ice buildup is cleared and its defrost cause fixed, and loose pans or tubing are secured. Compressor mount issues are corrected without opening the sealed system.

  • Refrigerator door gasket not sealingA dollar bill slides out of a closed door with no resistance, or you see frost or sweat along one edge. A leaking gasket lets warm, humid air in, which loads the coil with frost and keeps the compressor running.

    Typical culprits

    • Splits at the gasket corners after years of use
    • Rubber gone stiff and out of shape
    • Magnet inside the gasket too weak to pull the door tight
    • Door dropping because hinge parts are worn
    • Spilled food stuck on the gasket so it can't lie flat

    How the technician handles it

    The gasket is cleaned and inspected, door alignment and hinge wear are checked, and we test the seal all the way around. A worn gasket is swapped for the exact one your model takes, and the door is adjusted until it meets the cabinet evenly on every edge.

  • Fridge temperature going up and downOne day the milk is icy, the next it is lukewarm. A thermometer shows swings of several degrees. Fluctuation often comes from something that controls airflow or tells the board what the temperature is.

    Typical culprits

    • Air damper hanging up open or closed
    • Temperature sensor slowly drifting out of spec
    • Defrost cycles lasting too long or starting too often
    • Relay on the main board clicking erratically
    • Crowded shelves covering the vents that move air

    How the technician handles it

    The technician checks the vents and loading first, then tests the damper, thermistors and defrost timing. A sticking damper or drifting sensor is replaced; a control relay problem may mean a board. We confirm stable temperatures before leaving.

  • Refrigerator running all the timeThe compressor never seems to rest, and the back of the cabinet feels hot. In a San Antonio summer some extra run time is normal, especially in a garage, but nonstop running with weak cooling means something is restricting heat removal.

    Typical culprits

    • Condenser coil furred over with lint
    • Warm air getting past a tired door seal
    • A frosted evaporator, insulated by ice because defrost failed
    • Condenser fan spinning slowly or not at all
    • A spot next to the oven or in a sweltering garage

    How the technician handles it

    We clean the condenser coil, test the condenser fan, inspect the gaskets and look at the evaporator for frost. If placement is part of the problem, we talk through clearances and garage limits. The goal is normal cycling with steady temperatures.

  • Freezer icing up instead of defrostingWhite frost coats the freezer's back wall or covers the vents. Over days it chokes off airflow, and the fridge side starts warming. A frost-free freezer should never look like this.

    Typical culprits

    • Open circuit in the defrost heater
    • Defrost thermostat that never closes
    • Defrost timer or board that never starts the cycle
    • Door ajar for hours, loading the coil with moisture
    • Leaky gasket drawing in humid summer air

    How the technician handles it

    The technician melts the frost to reach the coil, then tests the heater, defrost thermostat and the timer or board. After the bad part is swapped, we force a defrost cycle to prove the repair. If you try to clear frost yourself, never chip at it with a sharp tool; one slip can puncture the coil.

  • Food freezing in the refrigeratorLettuce gets icy, eggs crack, and drinks at the back of a shelf turn slushy. The fresh-food section is getting more cold air than it needs, usually because the control that meters that air is not doing its job.

    Typical culprits

    • Damper jammed in the open position
    • Fridge sensor reporting warmer than the real temperature
    • Dial or setting turned too cold, or a faulty control
    • Groceries pressed right up against the cold-air vent
    • Main board failing to shut the damper on time

    How the technician handles it

    We look at the temperature setting and whether food is blocking the vent, then test the damper and fresh-food sensor. A stuck damper or bad sensor is replaced, and the temperature is verified with a probe thermometer.

  • Refrigerator completely deadNo light, no display, no hum. A fully dead fridge is often a power problem in the house rather than the appliance, but it can also be a failed power supply or burned connection inside.

    Typical culprits

    • Breaker or GFCI outlet has tripped
    • Cord damaged or plug scorched
    • Power supply on the control board dead, often after a surge
    • Burned wire connector at the compressor or overload
    • Demo or showroom mode left on, so lights work but nothing cools

    How the technician handles it

    Start with the breaker panel and any GFCI receptacle on that circuit. If there is power at the outlet, the technician tests the cord, the board supply and wiring connections, and checks for demo mode. Burned connectors and failed boards are replaced.

  • Refrigerator compressor not runningThe fans may run and the lights work, but the compressor stays silent or hums and shuts off. Before calling a compressor dead, the parts that start it need to be checked, since they fail far more often.

    Typical culprits

    • Bad start relay or overload protector
    • Run capacitor gone weak on models fitted with one
    • Compressor motor windings open or shorted
    • Drive board for a variable-speed compressor failed
    • Compressor locked up after years of running hot

    How the technician handles it

    The technician tests the relay, overload, capacitor and drive board, then measures the compressor windings. When the compressor itself is dead, replacing it is sealed-system work involving refrigerant recovery and recharge, and we'll talk through whether that makes sense given the unit's age.

  • Fridge clicking but not coolingYou hear a click from behind it every few minutes, a brief hum, then nothing. The compressor is trying to start and being cut off. Food will warm steadily until it is fixed.

    Typical culprits

    • Start relay with a cracked or burned element
    • Overload protector so worn it cuts out early
    • Voltage sagging on an extension cord or busy circuit
    • Compressor pulling heavy current when it tries to start

    How the technician handles it

    Plug the fridge directly into a wall outlet if it is on an extension cord. Relay and overload get tested, voltage is verified, and the compressor's current draw is measured. A failed relay or overload is a quick replacement; a compressor that will not start with good parts needs a larger conversation.

  • Dirty refrigerator condenser coilsThe coil under or behind the fridge is where heat from inside the box is released. Dust, pet hair and garage grime build up on it and act like a blanket. The fridge still cools, just slower, with longer run times and a warmer cabinet.

    Typical culprits

    • Front grille pulling in dust and pet hair
    • Fridge jammed against the wall with no air gap
    • Kick plate removed, so hot air loops back across the coil
    • Years since anyone vacuumed the coil
    • Dusty garage setting

    How the technician handles it

    Every six months, unplug the fridge and vacuum the coil using a brush attachment; do it more often with pets or in a garage. If the coil is badly packed or hard to reach, the technician cleans it fully and checks that the condenser fan is moving air.

  • Refrigerator condenser fan not spinningThe small fan near the compressor pulls air across the condenser coil. If it stops, the compressor overheats and trips, and the fridge warms. You may notice the back of the fridge getting unusually hot or a clicking from the overload.

    Typical culprits

    • Bearings in the fan motor locked up
    • Debris or a shifted drip pan stopping the blade
    • Burned-out winding in the fan motor
    • Fan getting no voltage from the control board

    How the technician handles it

    We check whether the blade turns freely, test the motor and confirm voltage from the board. If the motor is seized or open, we replace it and clean the coil while that area is open. If the board is not powering the fan, the board is tested next.

Show 14 more refrigerator problems
  • Freezer fan not workingInside the freezer, hidden behind the back panel, a fan draws air over the cold coil and sends it to both sides of the fridge. When it stops, the soft whir you normally hear with the freezer door shut goes quiet, and the fridge side warms quickly.

    Typical culprits

    • Motor worn out from years of round-the-clock duty
    • Frost from a defrost problem locking the blade
    • Door switch wrongly signaling an open door to the control
    • Fan circuit on the control board dead

    How the technician handles it

    With the freezer panel off, the technician looks for ice packed around the fan blade, then tests the fan motor and door switch. A failed motor is replaced. If frost caused the jam, the defrost system is repaired too, or the fan will lock up again.

  • Refrigerator defrost heater burned outA few times each day, the defrost heater warms the evaporator coil to melt off frost. When it fails, the frost keeps building until air cannot pass, and both compartments warm. This ranks among the usual reasons a refrigerator slowly gets warmer.

    Typical culprits

    • Heater burned through with age
    • Crack in a glass-tube style heater
    • Corrosion on the heater's wire terminals
    • Defrost thermostat open, so the heater never gets power
    • Control never calling for defrost

    How the technician handles it

    Once the frost is melted, the heater and defrost thermostat are checked for continuity, and we confirm the control is sending them power. We replace what failed and run a defrost cycle to make sure the coil clears.

  • Water under the fridge crisper drawersWater collects under the produce drawers or freezes into a sheet on the freezer floor. The defrost drain that should carry meltwater to the pan below is blocked or frozen.

    Typical culprits

    • Crumbs or debris plugging the drain hole
    • Ice in the drain line after the drain heater or heat clip failed
    • Slime and mold lining the drain tube
    • Drain hose kinked behind the back panel

    How the technician handles it

    We clear the drain with warm water, flush the tube and check the drain heater or clip that keeps it from freezing. We replace a heat clip that's missing or failed so the drain doesn't clog again within weeks.

  • Refrigerator refrigerant leakCooling fades gradually over weeks, the compressor runs constantly, and the coil may show frost in only one patch. Refrigerant isn't consumed over time; if the charge is low, the sealed system has a leak somewhere.

    Typical culprits

    • Pinholes eaten into the evaporator coil by corrosion
    • Line cracked by vibration or a rough move
    • Brazed joint leaking at the compressor or drier
    • Coil pierced by a knife or screwdriver used to chip ice

    How the technician handles it

    This is a technician-only repair. We locate the leak, repair the tubing or replace the part, install a new filter drier, then evacuate and recharge the system under EPA Section 608 rules. We discuss whether the repair is sensible for the age and type of fridge before starting.

  • Refrigerator control board problemFans or the compressor run at the wrong times, defrost never happens, or the display behaves oddly. The main board coordinates all of this, and when one relay or circuit fails, the symptoms can look like several problems at once.

    Typical culprits

    • Relay contacts pitted on the defrost or compressor circuit
    • Surge damage from a thunderstorm or a utility outage
    • Condensation reaching the board
    • Solder joints cracked after years of heat

    How the technician handles it

    The technician confirms that the components the board controls are good, then checks the board's outputs and inputs. When the board is the problem, we install the correct one for your model and run the fridge through its cycles.

  • Refrigerator temperature sensor faultyThe fridge runs too warm, too cold or swings between them, even though the fans and compressor test fine. A thermistor is a small sensor that tells the board the temperature, and when its reading drifts, every decision the board makes is off.

    Typical culprits

    • Sensor readings creeping off as it ages
    • Sensor wire nicked or pinched behind a panel
    • Moisture inside the sensor body
    • Sensor knocked loose from its clip

    How the technician handles it

    We compare the sensor's measured resistance with the manufacturer's chart for the real temperature. A drifting or damaged thermistor is replaced and remounted in its proper spot, and the wiring is checked along its run.

  • Refrigerator clicking from the backA click from behind the refrigerator that repeats every few minutes usually means the overload protector is shutting the compressor off as it tries to start. A single click now and then can be normal defrost timing.

    Typical culprits

    • Overload protector repeatedly shutting the compressor down
    • Start relay that clicks but never gets the compressor going
    • Dead condenser fan letting the compressor overheat
    • Mechanical defrost timer advancing loudly
    • Low voltage on a shared or extension-cord circuit

    How the technician handles it

    The technician checks whether the compressor is actually starting, tests the relay and overload, confirms the condenser fan runs and measures supply voltage. Repeated clicking with a warming fridge should be looked at promptly.

  • Fridge ice dispenser jammedThe ice maker fills the bin, but pressing the dispenser gives a whir and no ice, or nothing at all. Ice that thaws and refreezes in the bin welds into one block that the auger can't turn.

    Typical culprits

    • Bin ice melted and refroze into a solid block
    • Burned-out auger motor or stripped gear
    • Chute flap or its solenoid stuck
    • Ice in the chute from warm air leaking past the door

    How the technician handles it

    Dump the bin and break apart ice that has fused together. An auger that stays stuck gets its motor and the dispenser solenoid tested, along with a look at the chute and its door seal, and the failed part is replaced.

  • Refrigerator ice maker making very little iceIce is being made, but the bin never fills and the cubes are small. In July this is common because the freezer is working harder, but low water flow is often part of it too.

    Typical culprits

    • Old filter choking the water flow
    • Water pressure in the house running low
    • Freezer warmer than the setting says
    • Mineral sediment half-blocking the valve screen

    How the technician handles it

    Change the filter first. If production stays low, the technician checks the freezer temperature, measures water pressure at the valve and cleans or replaces a scaled valve.

  • No water from the fridge after changing the filterEverything worked until the new filter went in, and now the dispenser and ice maker get nothing. The problem is almost always the filter or air in the line, not the refrigerator.

    Typical culprits

    • New filter not twisted all the way into its lock
    • Generic filter that doesn't quite match the housing
    • Shipping caps still on the filter
    • Air trapped in the line after the swap

    How the technician handles it

    Take the filter out, look for any caps left on it, and push it back in until it locks firmly. Dispense water for a few minutes so air works its way out of the line. If water still does not flow, the technician checks the filter head and the inlet valve.

  • Water line frozen in the fridge doorThe dispenser stops while the ice maker keeps working, or both quit. The thin tube running through the door or into the freezer has frozen.

    Typical culprits

    • Freezer set colder than about −5°F
    • Cold air reaching the tube past a leaky gasket
    • Tube pressed against a cold surface
    • Door heater burned out (only on models equipped with one)

    How the technician handles it

    The technician thaws the line with warm air, then fixes the reason it froze: resetting the temperature, replacing the gasket, rerouting the tube or replacing the heater. Garage fridges with exposed supply lines should also be protected before a hard freeze.

  • Refrigerator sweating on the outsideBeads of water form on the cabinet between the doors or along the door edges. Humid weather can cause some of this, but heavy, constant sweating means a heater or seal is not doing its job.

    Typical culprits

    • Failed heater in the center post between French doors
    • Cold air leaking out past a worn gasket
    • Energy-saver mode switched on during humid weather
    • Door stopping short of sitting flat against the cabinet

    How the technician handles it

    Turn off the energy-saver mode first. The technician then tests the mullion heater, checks the gasket and door alignment, and replaces whatever has failed.

  • Refrigerator door won't close by itselfThe door swings back open, stops an inch short or needs a push to seal. A door left even slightly open loads the coil with frost and warms the food. Shifting slabs on clay soil can throw leveling off over time.

    Typical culprits

    • Front legs set too low, so the cabinet leans forward and the door won't swing shut on its own
    • Cracked door cam or closer
    • Worn hinge bushings
    • A drawer or bin sticking out into the door's path
    • Slab movement throwing the cabinet out of level

    How the technician handles it

    The technician adjusts the leveling legs so the cabinet tilts slightly back, checks bins and drawers, and replaces worn hinge parts or a broken cam. We start the door from partway open to make sure it swings shut and seals by itself.

  • Refrigerator showing an error codeA code or blinking pattern appears on the display, sometimes with an alarm. Codes point to a circuit, not necessarily a failed part, so they are a starting place for diagnosis.

    Typical culprits

    • A temperature sensor out of range
    • Fan not reaching the speed the board expects
    • Problem in the defrost circuit
    • Display and main board no longer communicating

    How the technician handles it

    Note the code before resetting anything. A code only names a circuit, so we look up its meaning for your model and test each part on it, since a loose connector or damaged wire can throw the same code as a failed component.

Brands

Refrigerator brands we repair

All brands →
  • Samsung logo
  • LG logo
  • Whirlpool logo
  • GE Appliances logo
  • Maytag logo
  • Bosch logo
  • KitchenAid logo
  • Frigidaire logo
  • Sub-Zero logo
  • Viking logo
  • Kenmore logo
  • Amana logo
  • Electrolux logo
  • Miele logo
  • Thermador logo
  • Admiral logo
  • Atosa logo
  • Avanti logo
  • Bertazzoni logo
  • Blomberg logo
  • Dacor logo
  • DCS logo
  • Everest logo
  • Fisher & Paykel logo
  • Gaggenau logo
  • Hoshizaki logo
  • Hotpoint logo
  • Insignia logo
  • JennAir logo
  • Perlick logo
  • Roper logo
  • Sharp logo
  • Smeg logo
  • Thor Kitchen logo
  • True Residential logo
  • Turbo Air logo
  • U-Line logo

From our technicians

Refrigerator repair notes for San Antonio homes

A refrigerator that has stopped cooling rarely gives a clean signal. The light comes on, something hums, and the freezer may still feel cold, so people wait to see if it sorts itself out. It almost never does, and the compressor works harder in the meantime.

The good news is that most warm-fridge calls are not compressor failures. They are fans that quit, defrost parts that burned out and left the coil buried in frost, condenser coils packed with dust, or a sensor sending the control board a wrong temperature. Those are parts a technician carries or can get quickly.

Below is how our technicians approach a refrigerator call in this city: what they check first, what homeowners tend to misjudge, and how heat, hard water and hard freezes shape the work.

The order we check a warm refrigerator

We start with the cheap things to rule out. Is the control set correctly? Does the door close on its own, or is a drawer holding it open a quarter inch? Is the fridge stuck in demo mode? Next we remove the kick plate to inspect the condenser coil and fan, since a clogged coil or seized fan shows up as a warmer fresh-food section within a day.

Next comes the freezer back panel. If the evaporator coil is a solid sheet of frost, defrost has failed and the fan cannot push air through it. The heater, defrost thermostat and control all get tested, and we confirm the evaporator fan is running at full speed. Only after airflow and defrost check out do we look at the compressor, its start parts and the sealed system.

What homeowners most often misread

The classic one is a cold freezer and a warm fridge. People assume the worst. In fact, most frost-free fridges cool both sides from one evaporator coil hidden in the freezer, and a fan sends that cold air through a duct to the fresh-food compartment. Lose that fan, or let the coil frost solid, and the freezer stays reasonably cold while the fridge creeps into the 50s. That is usually an airflow or defrost repair, not a dying compressor.

The second is water on the floor. Most people look at the water line first, but the usual source in a frost-free fridge is the defrost drain. Defrost water is supposed to run through a narrow tube into a pan by the compressor, and if that tube freezes or clogs, the water spills over inside and seeps out beneath the crisper drawers or at the front of the cabinet.

Heat, hard water and freezes: the San Antonio version of this appliance

Garage refrigerators here live a hard life. From June into September an attached garage can run well above the outdoor temperature, and a condenser can only shed heat into air cooler than itself. The compressor runs nearly nonstop, the coil pulls in dust, and start relays and condenser fans wear out faster. Some refrigerators are not rated for garage temperatures at all, so check the manual before moving the old kitchen fridge out there.

Water quality matters too. SAWS pulls our water from the Edwards Aquifer, and that hard water leaves mineral deposits in the dispenser, the fill tube and the screen on the inlet valve. Homes in the Hill Country on private wells can see sediment and sulfur on top of hardness. A slow dispenser or a weak ice maker is often a scaled screen or a filter that needs changing sooner than the calendar says.

Cold snaps cause their own damage. During the February 2021 storm, many garage fridges sat without power for days and supply lines along outside walls froze and split. Spring storms in San Antonio bring brief outages and surges that damage control boards, so a refrigerator that powered back up with a dark display or strange behavior should be looked at.

Repair or replace: how we talk it through

We do not publish prices, but we will tell you plainly what we think. Fans, defrost parts, thermistors, gaskets, valves and most door hardware are routine repairs on a refrigerator of almost any age. On mid-range and high-end models, replacing a control board is often worthwhile, particularly when the cabinet and sealed system are in good shape.

Sealed-system work is where the conversation gets real: refrigerant recovery, brazing and a fresh charge. On a built-in or newer premium model that can still make sense. On an older basic unit with worn gaskets and yellowed liners, we will say so, and you decide.

Owner care, safety, and what the visit looks like

Twice yearly, with the fridge unplugged and the bottom grille removed, run a vacuum over the condenser coil; a dusty San Antonio garage may call for it more often. Wipe the gaskets with warm soapy water, keep interior vents clear and change the water filter on schedule. Don't pry ice off the evaporator with a screwdriver or knife; a single slip can puncture the coil. Refrigerant is regulated, so recovering and recharging it is never a DIY job.

Booking includes a three-hour arrival window, set by our dispatcher on the call. Diagnosis happens first, then the technician walks you through what broke and quotes a single figure that covers both the part and the labor. The diagnostic fee is credited if you go ahead. Should a part need ordering, we tell you how many days it will take before you say yes, and we schedule the second trip before the technician packs up. Coverage after a repair: 90 days for any installed part, 30 days for the workmanship.

Questions

Refrigerator repair questions

The fridge section is warm even though the freezer stays cold. Is the compressor going?

Usually not. In most frost-free refrigerators the fridge gets its cold air from the freezer through a fan and a duct. Most often it's an evaporator fan that quit or a coil frosted over after the defrost system failed, and both are routine fixes.

Will a standard fridge hold up in a San Antonio garage?

Some do and some don't, so check the manual for the rated room temperature range first. A hot garage makes the condenser work hard in summer, so keep the coil clean and leave room around the cabinet. In a hard freeze, some models stop keeping the freezer cold because the room is colder than the thermostat expects.

Does hard water really affect my refrigerator?

It affects the parts that touch water. Sediment and scale collect in the inlet valve screen, dispenser line and ice maker fill tube, slowing the dispenser and cutting ice output. Changing the filter on time helps, and a clogged valve screen is a straightforward fix.

My fridge stopped working after a storm. What should I check?

Check the breaker and, if the fridge is on one, the GFCI outlet. If it has power but a blank display or will not cool, the control board or start components may have taken a surge. While you wait for us, resist opening the doors; every opening lets cold air escape.

Can you fix a refrigerant leak?

Often, yes. The technician finds the leak, repairs the tubing or replaces the affected part, then evacuates and recharges the system under EPA refrigerant rules. Whether the repair is worthwhile comes down to the leak's location and the fridge's age, and we'll tell you which way we'd go.

Need your refrigerator looked at?

Phone us at any hour, or send the online form and we ring back to set your three-hour window.

Call now, 24/7(210) 939-3313Book online