Whirlpool appliance repair in San Antonio, TX.
Phones staffed 24/7Three-hour arrival window90-day parts warranty
- Diagnosis
- The failed part is found before any price
- Approval
- No work begins without your okay
- Hours
- Calls answered day and night
- Warranty
- Parts 90 days · labor 30 days
Book online
Send the basics. A dispatcher calls you back.
- 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
- 2Pick up when we callWe confirm the address and set a three-hour arrival window.
- 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.
Would rather explain it out loud? Call us any hour, any day.
Schedule a repair
Step 1 of 2 · Appliance and area
Everyday brands
Whirlpool appliances we repair
- Whirlpool refrigerator
- Whirlpool washer
- Whirlpool dryer
- Whirlpool dishwasher
- Whirlpool oven
- Whirlpool microwave
- Whirlpool freezer
- Whirlpool cooktop
- Whirlpool range & stove
What fails most on Whirlpool
- Drive coupler worn out on direct-drive top-loaders
- Lid switch or door lock stopping the cycle
- Drain pump blocked by small items
- Defrost heater or thermostat failure on the fridge
- Dryer thermal cutoff tripped by a clogged vent
Error codes
Whirlpool error codes, decoded
What the display is telling you. Code meanings shift by model and year, so the technician verifies on the unit.
- Cabrio and agitator top-load washers
- Duet front-load washers
- French-door and side-by-side refrigerators
- Gold series dishwashers
- Gas and electric ranges
Whirlpool washer
- F8E1 / LF
- The washer is filling too slowly. Check the tap, the inlet screens for scale and the water valve.
- F9E1 / Ld
- Water is draining too slowly. Check the pump and its filter, look for a kinked hose, and see whether the hose goes too deep into the standpipe.
- F5E2
- The front-load door lock is not engaging.
- F7E1
- The control cannot read motor speed. Suspect the belt first, then the motor or the board that controls it.
- rL
- Remove load. At the start of a cleaning cycle, the machine detected clothes or water in the drum.
Whirlpool dryer
- AF
- Airflow is restricted. Look at the lint screen, the full vent path, and any section of duct that has been flattened.
- F22 / F23
- F22 flags an open exhaust thermistor; F23 flags a shorted one.
Whirlpool oven
- F3E1
- The oven temperature sensor is reading open or shorted.
- F1E1
- The control board has a fault.
Worth checking before you call
- • Long-drain code on the washer? If the drain hose goes deep into the standpipe, it can siphon and fool the control.
- • AF on the dryer? It is nearly always the vent, and a choked vent is a fire risk. Clear it before running another load.
From our technicians
Working on Whirlpool equipment
There is a good chance a Whirlpool is the most common appliance in your neighborhood, and from a repair standpoint that is good news. The designs are conventional, the faults are well known, and the parts catalogue is shared with Maytag, KitchenAid, Amana, JennAir and Roper. A part that sounds obscure is often sitting in a warehouse under a sister brand's name.
Whirlpool also sells most parts individually. A broken drive coupler is a small plastic piece, not a transmission. A dead dryer usually needs a fuse, not a control board. That keeps many repairs modest.
Across San Antonio we repair Whirlpool microwaves, cooktops, ovens, ranges, dishwashers, dryers, washers, freezers and refrigerators. The technician finds the fault first and gives you one price before any work starts.
What sets Whirlpool apart
Whirlpool is the parent of Maytag, KitchenAid, Amana, JennAir and Roper, and a great many parts move freely between those badges. Its refrigerators are laid out conventionally, pairing a standard compressor and timed or adaptive defrost with a fan that circulates cold air between the sections. Whirlpool sells pumps, valves, couplers, switches and fuses as individual parts rather than whole assemblies. Older machines signal faults with blinking lights, while newer ones display short codes such as F8E1 or AF.
Because one parts catalogue serves several brands, a number that has been dropped under the Whirlpool name is often still available under another badge, and we check that before ever calling a part unavailable. On top-load washers we test the coupler, lid switch and drain pump in a sensible order so the cabinet does not get opened for nothing. On dryers that stop heating, the vent and the thermal cutoff come before the element. Common Whirlpool parts ride on the van.
The usual suspects on Whirlpool laundry
On direct-drive top-loaders, a washer that fills and agitates weakly or not at all but makes a motor hum usually has a worn drive coupler. When one will not spin, the lid switch has often stopped reporting that the lid is shut. A slow-drain code, F9E1 or Ld, is frequently a sock in the pump. We test those three in that order, and most of the time the cabinet never has to come apart.
Whirlpool dryers are tough. When one runs but will not heat, we look at the vent and the thermal cutoff before the element, because a clogged vent is what trips the cutoff in the first place. Put in a new fuse while the vent stays clogged, and the fuse will pop again.
What San Antonio does to a Whirlpool
Plenty of local houses route dryer exhaust through the attic to a roof cap. Those runs are long, hot and full of bends, and lint builds up fast. An AF code on a newer Whirlpool dryer means restricted airflow, and in these homes it is almost always the vent. We will tell you if the run needs a professional cleaning.
Hard SAWS water is the other factor. Scale narrows washer inlet screens and dishwasher fill valves, so fills slow down and F8E1 or LF codes appear. On the refrigerator, a scaled inlet valve gives you a weak dispenser and small cubes. Cleaning screens helps; a valve that is crusted inside gets replaced.
Whirlpool refrigerators and the defrost system
When a Whirlpool fridge is warm on the fresh-food side but the freezer still feels cold, a defrost fault is the usual cause. The heater or its thermostat stops melting frost off the coil, ice chokes the airflow, and the fan cannot push cold air down. It looks like a compressor problem and almost never is. Garage refrigerators in July add strain, so we also check that the condenser coil and fan are clean and running.
When to repair, and what to have ready
Most Whirlpool repairs are worth doing because the parts are affordable and easy to get. The exception is an older refrigerator with a failed sealed system, where the numbers can lean toward replacement, and we say so. Find the model and serial label before calling: inside the fridge on a wall, on a washer beneath the lid or on the console's back, and inside the dryer door opening.
Questions
Whirlpool repair questions
My Whirlpool washer shows F8E1 / LF. What is it telling me?
The washer is filling too slowly. Check the tap, the inlet screens for scale and the water valve. The same code can mean something slightly different across models and years, so our tech checks it on your unit before pricing anything.
My Whirlpool washer shows F9E1 / Ld. What is it telling me?
Water is draining too slowly. Check the pump and its filter, look for a kinked hose, and see whether the hose goes too deep into the standpipe. The same code can mean something slightly different across models and years, so our tech checks it on your unit before pricing anything.
My Whirlpool washer shows F5E2. What is it telling me?
The front-load door lock is not engaging. The same code can mean something slightly different across models and years, so our tech checks it on your unit before pricing anything.
Can a part made for my Whirlpool come labeled Maytag or KitchenAid?
Yes, often. The brands share one parts system, and the same number can ship under different names. We match by part number, not by the logo on the box.
My Whirlpool washer shows F9E1 but the drain looks clear. What else causes it?
If the drain hose sits too far down the standpipe, it can siphon water out and throw off the control. The pump itself or its filter can also be partly blocked. We check both.
Why does my dryer's AF code keep coming back after I clean the lint screen?
The restriction is further along, usually in a long attic run or at the roof cap. Start at the lint screen, but do not stop there. Until the full vent is clear the code will return, and the dryer is a fire risk in the meantime.
Whirlpool acting up?
Tell us the model and the symptom. A person answers 24/7.