Dishwasher repair in San Antonio, fixed at your place.
Phones staffed 24/7Three-hour arrival window90-day parts warranty
- Diagnosis
- The failed part is found before any price
- Approval
- No work begins without your okay
- Hours
- Calls answered day and night
- Warranty
- Parts 90 days · labor 30 days
Book online
Send the basics. A dispatcher calls you back.
- 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
- 2Pick up when we callWe confirm the address and set a three-hour arrival window.
- 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.
Would rather explain it out loud? Call us any hour, any day.
Schedule a repair
Step 1 of 2 · Appliance and area
- 1–2 hours
- Typical time on site
- 30
- Dishwasher faults we fix
- 27
- Brands we service
- 24/7
- Phones answered
Dishwasher problems
What is wrong with your dishwasher?
Pick a symptom for the usual causes and the fix a technician makes.
Dishwasher not cleaning dishesFood stays stuck on plates, cups come out gritty, and the dishes look like they were only rinsed. Before blaming a pump, check the filter and spray arms, which clog fast with food and hard-water scale.
Typical culprits
- Clogged filter starving the wash pump of water
- Spray arm jets plugged with seeds, glass chips or scale
- Wash pump motor weak or its impeller worn
- Water never getting hot enough to wash well
- Tall pans or bowls blocking the spray arms
How the technician handles it
Clean the filter and spray arms first. Still no luck? We measure how much water comes in, how hot it is and how hard the wash pump pushes it, then replace the heater or pump if either has quit.
Dishwasher not drainingAfter the cycle ends, a pool of murky water is still left at the bottom of the tub. The blockage can be anywhere from the filter to the sink drain, and the pump is only one of the suspects.
Typical culprits
- Food packed into the filter and sump
- Drain hose folded or pinched beneath the sink
- Clogged inlet on the garbage disposal
- Broken glass jamming the drain pump
- Blocked air gap on the sink
How the technician handles it
Clean the filter and run the disposal. The technician checks the air gap, hose and disposal connection, then tests the drain pump and clears or replaces it.
Dishwasher leaking on the floorYou find water on the floor beneath the dishwasher or along its front. Over a slab floor, water can travel under cabinets and flooring before it ever shows, so don't run the machine until we find where it's coming from.
Typical culprits
- Worn or torn door gasket
- Leaking seal on the pump
- Loose inlet valve or hose fitting
- Foam from too much or the wrong detergent
- Machine not sitting level
How the technician handles it
Turn off the water supply and power. The technician removes the kick plate, finds the source, and replaces the gasket, seal or fitting, or relevels the machine.
Dishwasher won't turn on or startPressing start does nothing, or the display lights up but water never comes in. Many of these are latch, lock or power issues.
Typical culprits
- Door latch switch not making contact
- Control or child lock engaged
- Blown thermal fuse on the control
- Failed control board
- Power cut off at a wall switch or breaker
How the technician handles it
Check the breaker, any switch under the sink, and the control lock. The technician tests the latch, thermal fuse and board and replaces what failed.
Dishwasher not drying dishesCups and plastic containers in particular are still wet when you unload. Some moisture is normal on newer models, but dripping-wet loads usually point to rinse aid or heat.
Typical culprits
- Burned-out heating element
- Rinse aid dispenser empty
- Drying vent or fan stuck on models that use one
- Failed high-limit thermostat
- Heated dry option switched off
How the technician handles it
Fill the rinse aid and turn on heated dry. If dishes are still wet, the technician tests the element, thermostat and vent.
Dishwasher door won't latchThe door will not latch, or it latches but the machine says it is open. Without a closed latch, the dishwasher will not start.
Typical culprits
- Broken door latch
- Bent strike on the tub
- Rack not pushed all the way back
- Tub racked out of square by loose mounting brackets
How the technician handles it
Push the racks fully in. The technician checks the latch, strike and mounting, replaces a broken latch and resecures the tub.
Dishwasher making loud noiseGrinding, rattling or a loud hum during the wash. Some water sounds are normal, but grinding usually means something is in the pump.
Typical culprits
- Glass shard or bone caught in the pump
- Spray arm striking a tall item
- Worn bearing in the wash pump
- Noisy drain pump
- Loose mounting brackets
How the technician handles it
Check for anything blocking the spray arms. The technician clears debris from the pumps and replaces worn pumps or tightens mounting.
Dishwasher not getting waterThe machine hums but no water comes in, or very little. Hard water and well sediment often clog the inlet screen.
Typical culprits
- Dead inlet valve solenoid
- Inlet screen crusted with scale or sediment
- Float switch stuck up
- Supply line kinked or shutoff closed
How the technician handles it
Look under the sink and confirm the dishwasher's supply valve is all the way open. The technician checks the float, cleans the screen, tests the valve and replaces it if needed.
Dishwasher stinksA sour or rotten smell when you open the door. Food trapped in the filter or water sitting in the sump is usually the cause.
Typical culprits
- Food rotting in the filter
- Water sitting in the sump between loads
- No high loop in the drain hose, so sink water flows back
- Grease and scraps in the door gasket
- Clogged disposal pushing waste back into the hose
How the technician handles it
Clean the filter and gasket and run a cleaning cycle. If the smell keeps coming back, the technician checks that the drain hose has its high loop and that its hookup to the disposal is sound.
Dishwasher detergent cup won't openWhen the cycle finishes, the detergent is still in the dispenser cup. Dishes come out dirty.
Typical culprits
- Broken dispenser latch
- Failed actuator coil
- Old detergent caked around the cup
- A tall plate or pan in the way of the cup lid
How the technician handles it
Clean the cup and check for blocking dishes. The technician tests the actuator and replaces the dispenser if needed.
White spots or film on dishesGlasses come out with white spots or a chalky haze. In San Antonio, hard water is the usual reason.
Typical culprits
- Minerals from hard water
- Empty rinse aid dispenser
- Detergent dose too low or too high
- Wash water not hot enough
- Hardness setting wrong for softened water
How the technician handles it
Fill the rinse aid, use the right detergent dose and set the hardness level. If spots persist, the technician checks water temperature and the heater.
Dishwasher stopping before the cycle endsThe cycle stops early, leaving water or soap. The machine is detecting something wrong or losing power to the controls.
Typical culprits
- Latch switch cutting in and out
- Control overheating or a bad thermostat
- Leak float lifted by water in the base
- Fault in the control board
How the technician handles it
The technician checks the door switch, thermostat and leak sensor, then the board.
Dishwasher drain pump not workingThe pump hums or stays silent and the water does not leave. Broken glass is a common culprit.
Typical culprits
- Glass or bone jamming the impeller
- Burned-out pump motor
- Damaged pump wiring
- Check valve stuck shut
How the technician handles it
Turn off power. The technician frees the impeller, checks the pump motor and wiring with a meter, and swaps the pump when the motor is shot.
Dishwasher filter cloggedAt the bottom of the tub, a filter catches food so it isn't sprayed back onto the dishes. When it clogs, the dishwasher cleans poorly and may not drain.
Typical culprits
- Grease and food packed into the mesh
- Filter left uncleaned for months
- Broken glass sitting in the sump
- Fine filter cracked so debris gets into the pump
How the technician handles it
Turn the filter to release it, hold it under warm running water, and work the mesh over with a soft brush. Replace a cracked filter.
Dishwasher wash pump not sprayingThe tub fills but you do not hear spraying, and dishes come out dirty. The wash pump is not pushing water to the spray arms.
Typical culprits
- Dead wash motor
- Broken impeller
- Failed start capacitor on the motor
- Glass, pits or bones lodged in the pump
How the technician handles it
The technician clears debris, tests the motor and capacitor, and replaces the pump or motor.
Dishwasher spray arms cloggedSpray arms do not spin or spray weakly, leaving dirty spots. Hard-water scale and small debris block the holes.
Typical culprits
- Jets plugged with scale
- Cracked spray arm bearing
- A dish stopping the arm
- Loose spray arm hub
How the technician handles it
Remove the arms, clear the holes with a toothpick and soak them in vinegar to loosen scale. Replace cracked arms.
Show 14 more dishwasher problems
Dishwasher heating element not workingDishes come out cool and wet, and cycles may run long. Many dishwashers heat their own water for washing and drying.
Typical culprits
- Element burned through
- Failed high-limit thermostat
- Sensor reading the wrong temperature
- Burned relay on the board that powers the heater
How the technician handles it
The technician tests the element, thermostat, thermistor and relay, and replaces the faulty part.
Dishwasher control board problemThe dishwasher is dead, behaves erratically or skips steps. Surges from storms and water leaks are common causes.
Typical culprits
- Surge from a storm or outage
- Water dripping onto the board from a leak
- Burned relay or circuit trace
- Faulty keypad sending phantom commands
How the technician handles it
The technician tests the components first, then the board. A faulty board is replaced, and if water reached it, the leak behind that is fixed as well.
Dishwasher cycle taking too longA wash now takes far longer to finish than it once did. The machine is waiting for something, usually water temperature or fill.
Typical culprits
- Weak or failed heater
- Cold water reaching the machine
- Soil sensor adding extra rinses
- Inlet screen scaled up, so filling takes longer
How the technician handles it
Run the kitchen tap hot before starting. The technician checks the heater, inlet screen and sensors.
Dishwasher showing an error codeThe display shows a code or lights flash in a pattern. Codes point to a circuit, which is the place to start testing.
Typical culprits
- Drain path plugged
- Leak float lifted by water in the base
- Problem with the heater or a temperature sensor
- Faulty door switch
How the technician handles it
Note the code. We look up what that code means on your model, then test the circuit it flags.
Dishwasher leaking from the doorDrips or a small puddle form under the door corners after a load. A worn gasket, an overfilled tub or suds from the wrong soap are the usual reasons.
Typical culprits
- Gasket torn or crushed flat
- Hinges out of adjustment
- Overfill from a stuck valve
- Suds from the wrong detergent
- Machine not level side to side
How the technician handles it
Use only dishwasher detergent. The technician checks leveling, the gasket, the hinges and the fill level.
Dishwasher leak sensor trippedThe dishwasher stopped, may be draining nonstop, and shows a leak code. The sensor is working as intended: water has pooled in the base.
Typical culprits
- A dripping internal hose filling the base pan
- Leaking pump seal
- Foam spilling over
- Water supply connection not tight
How the technician handles it
The technician tracks down and repairs the leak, dries out the base and makes sure the sensor resets. Do not disable the sensor.
Dishwasher overfillingWater rises near the door or spills out. That is a flood risk and a reason to stop the machine.
Typical culprits
- Fill valve that won't close
- Float switch stuck down
- Failed pressure sensor
- Board leaving the fill valve powered too long
How the technician handles it
Turn off the water supply and power. The technician tests the valve, float and sensor and replaces the faulty part.
Dishwasher humming but not washingThere is a steady hum and no sound of spraying water. The motor has power but cannot turn, usually because something is jammed in the pump or a start part has failed.
Typical culprits
- Seized wash motor
- Something hard wedged in the impeller
- Failed start capacitor
- Worn motor bearings
How the technician handles it
Any debris is cleared, the capacitor and motor are tested, and a seized motor is replaced.
Dishwasher top rack not cleaningBottom rack dishes come out clean but the top rack stays dirty. The upper spray arm is not getting water.
Typical culprits
- Jets on the middle or upper arm plugged
- Rack not docking with its water feed
- Cracked feed tube
- Spray arm hitting a tall pan or board in the bottom rack
How the technician handles it
Clean the upper arm and check for tall items. The technician checks the rack docking and feed tube.
Water spurting from the sink air gapWhen the dishwasher pumps out, water bubbles up out of the little chrome cap beside the faucet. Something below the air gap, in the hose or the disposal, is blocked.
Typical culprits
- Food stuck in the air gap
- Disposal inlet clogged
- Pinched hose running from the air gap to the disposal
- Kitchen sink drain partly clogged
How the technician handles it
Remove the air gap cap and clean it. The technician clears the hose and disposal inlet.
Dishwasher won't drain after a new disposalThe dishwasher drained fine until the new disposal went in. New disposals often come with the dishwasher inlet plugged.
Typical culprits
- Knockout plug still in the new disposal
- Hose clamp cranked too tight
- Drain hose crushed behind the disposal
- Clogged disposal inlet
How the technician handles it
Disconnect power to the disposal. The technician removes the knockout plug and reconnects the hose correctly.
Dishwasher rinse aid not dispensingThe rinse aid level never goes down, and glasses come out spotted.
Typical culprits
- Rinse aid cap or valve gummed up
- Setting turned too low
- Failed actuator
- Cracked dispenser leaking
How the technician handles it
Check the rinse aid setting. The technician tests the dispenser and replaces it if needed.
Dishwasher door drops openThe door falls open hard when you release it, or it won't hold its position partway down. The springs or cables that balance it have failed.
Typical culprits
- Broken door spring
- Cable snapped or off its pulley
- Worn hinge
- Loose spring link
How the technician handles it
The technician replaces the springs or cables in pairs and checks the hinges.
Dishwasher buttons not respondingSome or all buttons do not respond. The control may be locked or the touchpad may have failed.
Typical culprits
- Worn-out touchpad membrane
- Control or child lock engaged
- Loose ribbon cable
- Failed control board
How the technician handles it
Check for the control lock. The technician tests the touchpad and board and replaces the failed part.
Brands
Dishwasher brands we repair
From our technicians
Dishwasher repair notes for San Antonio homes
Ask a San Antonio homeowner what is wrong with their dishwasher and a good share will describe the same thing: glasses with a white haze, a gritty feel on plates, a machine that is not cleaning the way it used to. Some of those are repair calls. Many are water and detergent problems that look like repairs.
That is not to say dishwashers here do not break. Drain pumps catch broken glass, inlet valves scale up, door latches wear and control boards take hits during storms. But knowing which problem is which saves time and money.
These notes walk through how hard water and softeners change dishwasher behavior, how our technicians trace drains and leaks, and what you can safely handle yourself.
Hard water changes everything here
SAWS water from the Edwards Aquifer is hard. Inside a dishwasher, that hardness shows as cloudy spots on glassware, crusty spray arm jets, scale on the heating element and a clogged inlet valve screen. Scale in the spray arms reduces pressure, so dishes on the edges come out dirty. Scale on the inlet screen slows the fill, so the machine runs a cycle with less water than it should.
The fix starts with detergent and rinse aid, not parts. Use a quality detergent at the dose the package recommends for hard water, keep the rinse aid filled, and run a dishwasher cleaner occasionally. Many dishwashers also have a water hardness setting, usually buried in a settings menu; setting it correctly changes how the machine doses and rinses.
Softeners and Hill Country wells
Plenty of San Antonio homes have water softeners, and softened water changes the rules. Soft water needs less detergent. Use the hard-water dose with soft water and you can get foam, a film that looks like hard-water spots, and over time etching that permanently clouds glass. If your home has a softener, cut back on detergent and set the dishwasher's hardness level to soft.
Homes in Helotes, Bulverde, Boerne and other Hill Country areas on private wells can have very hard water, sulfur, iron or sediment. Sediment clogs inlet screens and filters faster, and sulfur can leave an odor in the tub. A whole-house filter or softener helps, and cleaning the inlet screen becomes routine maintenance.
Draining problems: check the sink side first
When water is left in the bottom after a cycle, most people assume the drain pump has failed. Often it has not. Water leaves through the filter and sump, passes through the pump, climbs a hose to an air gap or high loop under the counter, and empties into the disposal or the sink's drain line. A blockage anywhere in that run stops the drain.
Our technicians work through it in order: filter and sump first, then the air gap if there is one, then the hose and disposal connection. We often see it right after a disposal swap, when nobody punched out the new unit's knockout plug. We test the pump only once the whole drain path is confirmed clear. A pump jammed with broken glass or a piece of bone is common, and sometimes the impeller can be cleared without replacing the pump.
Leaks: usually not where people look
A puddle at the front of the dishwasher points everyone toward the door seal, and now and then that guess is right. Just as often the cause is too much detergent or the wrong kind making foam, a dishwasher out of level side to side, a pump seal leaking under the tub, or an inlet fitting that has worked loose behind the kick plate. On a slab, water creeps under cabinets without a sound, so even a slow leak can cause real damage before you notice.
A lot of newer dishwashers have a sensor in the base that detects leaks. When that sensor finds water, it shuts the machine down and may turn on the drain pump. A tripped sensor is not the problem; it is the alarm. We find the water's source, repair it, dry the base and check that the sensor resets.
Safe owner care, repair decisions and the visit
Before your hand goes into the sump, unplug the dishwasher or switch it off at the breaker. Clean the filter every week or two, pull the spray arms and clear their holes with a toothpick, and wipe the door gasket. Before you disconnect anything, close the water valve beneath the sink. Never run the dishwasher with the kick plate off or the leak sensor disconnected.
Pumps, valves, latches, heaters, sensors and springs are routine fixes. A new control board often pays off on a better-built machine. A rusted-through tub or a leaking tub seam usually means replacement. Phone us or book online; the dispatcher then pencils you into a three-hour slot; the technician explains the fault and quotes one number for the whole job, with the diagnostic fee deducted if you approve.
Questions
Dishwasher repair questions
What leaves a cloudy haze on glasses coming out of the dishwasher?
In hard water the cause is usually mineral film, and rinse aid plus the correct amount of detergent help. With a softener, it may be too much detergent, which can etch glass over time. Do a vinegar test: film that comes off with vinegar is mineral buildup, and film that stays may be etching.
Should I change my dishwasher settings if I have a water softener?
Yes. Many dishwashers have a hardness setting in the menu. Set it to soft, and reduce detergent. Too much detergent with soft water causes foam and film.
My dishwasher will not drain. Is the pump bad?
Check the filter, the air gap and the disposal connection first. Usually the cause is a clogged filter or blocked air gap, not a dead pump. When those are clear and the pump hums but no water leaves, suspect a jammed impeller.
Water is coming out of the air gap on my sink. What does that mean?
The drain path between the air gap and the disposal or sink drain is blocked. Clean the air gap cap and check the hose and disposal inlet. If it keeps happening, a technician can trace the blockage.
My dishwasher stopped working after a storm. What should I check?
Check the breaker and any switch under the sink. A unit that has power yet won't start may have a control board damaged by a surge. A technician can test it.
Is it worth repairing an older dishwasher?
If the tub is sound and the repair is a pump, valve, latch or heater, usually yes. If the tub is rusted or leaking, or several major parts have failed, replacement often makes more sense. We will tell you plainly.
Where we go
Dishwasher repair across the San Antonio area
- Downtown, Southtown & King William
- Alamo Heights & Terrell Hills
- Monte Vista, Tobin Hill & Olmos Park
- Woodlawn Lake & Balcones Heights
- East Side, Kirby & Fort Sam Houston
- West Side, Port San Antonio & Lackland
- Highland Park & Southeast San Antonio
- South Side & the Missions
- Medical Center & Oak Hills
- Leon Valley
- Castle Hills & North Central
- Shavano Park & Hunters Creek
- Hollywood Park & Thousand Oaks
- Stone Oak & Timberwood Park
- Windcrest & Northeast San Antonio
- Live Oak
- Universal City
- Converse
- Helotes & Braun Station
- UTSA Area & Great Northwest
- Alamo Ranch & Westover Hills
- The Dominion & Leon Springs
- Von Ormy, Atascosa & South Bexar
- Adkins, St. Hedwig & Elmendorf
- Schertz
- Cibolo
- Seguin & Marion
- Bulverde
- Garden Ridge
- New Braunfels
- Canyon Lake & Spring Branch
- Boerne, Fair Oaks Ranch & Bergheim
- Castroville, La Coste & Medina Lake
- Hondo
- Pipe Creek
- La Vernia
- San Marcos
Other appliances
Need your dishwasher looked at?
Phone us at any hour, or send the online form and we ring back to set your three-hour window.