Jump to main content
Hobart logo

Hobart appliance repair in San Antonio, TX.

We service Hobart dishmachines as light-commercial equipment, and in San Antonio that means fighting scale first.

Phones staffed 24/7Three-hour arrival window90-day parts warranty

Diagnosis
The failed part is found before any price
Approval
No work begins without your okay
Hours
Calls answered day and night
Warranty
Parts 90 days · labor 30 days

Book online

Send the basics. A dispatcher calls you back.

  1. 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
  2. 2Pick up when we callWe confirm the address and set a three-hour arrival window.
  3. 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.

Would rather explain it out loud? Call us any hour, any day.

Schedule a repair

Step 1 of 2 · Appliance and area

Step 1 of 2

Appliance and area

Which appliance?

Appliance

Where in the San Antonio area?

Booking costs nothing, and we never ask for a card.

Prefer to call? (210) 939-3313

Light commercial

Hobart appliances we repair

What fails most on Hobart

  • Scale collecting in the booster heater and the rinse arms
  • Wash or rinse jets plugged with scale or debris
  • Fill or drain valve sticking
  • Chemical pump or dosing line faults
  • Worn door seals, or curtains on conveyor machines

Commercial equipment

Servicing Hobart equipment

Hobart builds commercial equipment: gear-driven mixers and slicers, and dishmachines that have to reach a sanitizing rinse temperature. Dishmachine calls are mostly about wash or rinse water running too cool, which leads to the booster heater or the thermostat that controls it. Pumps and drain valves come up too. For mixers, it is usually trouble shifting speeds or gear noise. We schedule around your service hours.

  • LXe undercounter dishmachines
  • AM Series door-type dishmachines
  • Conveyor dishmachines
  • Older mixers
  • Slicers and food processors

Worth checking before you call

  • • If the rinse is not getting hot enough, measure the incoming hot water temperature first. If the incoming water is hot enough, check the booster heater next.

From our technicians

Working on Hobart equipment

A Hobart dishmachine is the quiet engine of a lot of San Antonio kitchens: an undercounter unit behind a bar, a door-type machine at a busy restaurant, a dishroom in a church hall that runs hard after Sunday lunch. When it stops, plates stack up within the hour.

These machines are meant to be maintained and rebuilt rather than scrapped, and most of what we find is wear and water, not design flaws. That usually means a faster, more contained repair than people expect.

What sets Hobart apart

Hobart builds commercial food equipment as part of ITW's food equipment group, the same group that includes Vulcan. Its dishmachines suit working kitchens: cycles are short and hot, the wash and rinse arms have jets that clear individually, and chemical dosing is automatic, while high-temperature models also carry a booster heater that raises the last rinse to sanitizing heat. The brand also makes gear-driven mixers and slicers. Hobart designs its equipment to be delimed and rebuilt and to stay in service for years, and wear parts for it remain available a long time.

With Hobart dishmachines, most of the trouble we see comes from the water: mineral scale coating the booster heater and the rinse arms, jets that plug up, or a sticking fill or drain valve. When the rinse never gets hot enough, look first at the incoming water, then the booster, then scale; a dead control is less likely, so it comes last. We treat Hobart as light-commercial equipment, schedule around your service hours when possible, and leave a written record of each visit.

Limestone and the booster heater

SAWS water comes largely from the Edwards Aquifer, and it carries a lot of limestone. In a high-temperature Hobart, that scale coats the booster heater element, lines the rinse arms and narrows the jets. The result is a final rinse that will not come up to temperature, or a weak, uneven spray that leaves dishes spotted.

Regular deliming is part of running a dishmachine here, not an extra. When a machine underperforms, incoming hot water temperature gets checked first, the booster second and scale third, and a deliming by itself solves more calls than you'd expect.

Valves, pumps and chemicals

Fill and drain valves stick when scale or food debris gets into them, which shows up as overfilling, underfilling or a tank that will not drain. Chemical dosing pumps and their lines wear and crack over time, and a machine that is not dosing correctly can leave a film or fail to sanitize on low-temperature models.

If you have a water treatment system or a chemical supplier who services the dosing equipment, tell us when you call. It helps us separate their part of the system from ours.

Booking a commercial call

Tell us the model, whether it is a high-temperature machine with a booster or a low-temperature chemical machine, and what the gauges or display are showing. Note when it was last delimed. That information narrows the diagnosis before we arrive.

We try to book outside your rush when the kitchen can wait. We also work on Hobart mixers with shifting trouble or gear noise and on slicers, so mention any of those for the same visit.

Questions

Hobart repair questions

Our Hobart will not reach final rinse temperature. Is the booster dead?

Not necessarily. Check the temperature of the hot water feeding the machine first. If that is right, the booster element, its thermostat or scale on the element are next, and we test all three.

How often should we delime our dishmachine?

Follow the manufacturer's guidance and your chemical supplier's advice. On hard San Antonio water, most kitchens need to delime more often than the minimum.

Can you look at our Hobart mixer too?

Yes. Speed shifting problems and gear noise on mixers are common jobs, and it is easier to handle both in one visit.

Do you handle Hobart warranty claims?

No. We do not perform manufacturer-warranty work. If your machine is still under warranty, contact the dealer or the manufacturer first.

Hobart acting up?

Tell us the model and the symptom. A person answers 24/7.

Call now, 24/7(210) 939-3313Book online