Appliance repair questions, answered
Phones staffed 24/7Three-hour arrival window90-day parts warranty
- Diagnosis
- The failed part is found before any price
- Approval
- No work begins without your okay
- Hours
- Calls answered day and night
- Warranty
- Parts 90 days · labor 30 days
Book online
Send the basics. A dispatcher calls you back.
- 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
- 2Pick up when we callWe confirm the address and set a three-hour arrival window.
- 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.
Would rather explain it out loud? Call us any hour, any day.
Schedule a repair
Step 1 of 2 · Appliance and area
13 questions · answered here
Can we fix it?
The faults we get called about most, what is usually behind each one, and what fixing it takes. Worth a read before you pick up the phone.
A cooktop burner won't light or won't heat. Can you fix it?
Yes. Listen to it first. A gas burner that clicks but never catches usually has a dirty or cracked igniter, clogged burner ports or a weak spark module. Hearing no click at all? Suspect the spark module, or the switch mounted behind that burner's knob. On an electric cooktop, a cold burner is the element, its receptacle or the control switch. If the part is on the truck, it gets done in one visit. Smell gas? Get out of the house without flipping any switches, and call CPS Energy or 911 before anyone else.
Can you fix a washer that won't spin?
Yes. Usually the washer isn't draining, and a tub with water in it won't spin. The cause is typically a plugged pump filter, a pinched drain hose or a small object jammed in the pump. If the drain checks out, the lid or door lock gets tested next, followed by the belt on models that have one. A failed motor control board is the last thing we look at, not the first.
Can you replace the heating element in my dryer?
Yes. Electric dryer elements fail often, but rarely without a reason. A restricted vent lets the element overheat until it breaks or the high-limit cutoff trips. Lots of San Antonio dryers vent up into the attic and out a roof cap, and lint packs those long runs tight. So after the new element is in, we check airflow all the way out. On gas dryers the parts differ: an igniter, a flame sensor and the gas valve coils.
Can you replace a refrigerator or freezer door gasket?
Yes. A gasket that's torn, flattened or pulling loose lets warm, humid air in. You see frost on the walls, the door edge sweating, or a compressor that almost never cycles off. That is a bigger deal in a garage fridge during summer. Sometimes the door just needs to be realigned, or the gasket reseated, and no part is needed. If it does need replacing, it has to be the gasket made for your model, so send a photo of the model sticker when you book.
My ice maker stopped making ice. Can you repair it?
Yes, both ice makers built into a refrigerator and standalone undercounter units. Common culprits: an iced-up fill tube, a weak inlet valve, a plugged filter, or a module that has stopped running the ice maker through its cycle. In San Antonio we also find a lot of scale in the valve screens and fill tubes from hard water. We check the water supply first, since a half-shut valve behind the fridge looks exactly like a failed ice maker.
The microwave runs but doesn't heat. Is that fixable?
Often. A working light and turning plate with food that stays cold means the high-voltage circuit has failed. Most often it's a door switch, the capacitor, the magnetron or the high-voltage diode. Please don't open it yourself. Even unplugged, a microwave's capacitor can still store a dangerous charge. With a cheap countertop microwave, the fix can cost nearly what a new one does, and we tell you that before starting.
My dishwasher door drops open. Can you fix that?
Yes. If the door drops open or won't hold its position, the cause is nearly always a broken spring or hinge cable. Both springs get replaced together, because the second one is just as worn. The job is quick, though some models need the dishwasher slid out of its cabinet to get to them.
Is a wine cooler that won't stay cold repairable?
Yes, compressor models and thermoelectric ones. With a compressor cooler, start by checking for dust on the condenser, a dead fan or a bad start relay. A slow refrigerant leak is less common. Thermoelectric coolers use a Peltier module plus fans, and a warm room overwhelms them, which in a Texas summer can mean any room by a west-facing window. Built-in coolers often fail because the front grille is blocked.
Can you fix a refrigerator compressor?
Sometimes. Often the compressor itself is fine; what failed is a part that starts or drives it, such as the overload protector, the start relay, or the inverter board on newer models. Those are fast repairs. A compressor that has truly failed is a bigger job. The refrigerant is recovered, a new compressor is brazed in and the system is recharged, all under EPA Section 608 rules. On an older entry-level fridge, that job can run past what the whole fridge is worth, and you'll hear so from us before anything starts.
Can you repair a cracked glass cooktop?
Usually, by replacing the glass top. Most radiant and induction cooktops treat the glass as its own part, and because the elements and sensors sit right underneath, only glass matched to your exact model will do. If the glass top is cracked, don't use it until the top is replaced. A spill can run through the crack onto live wiring.
My washer drum bangs or won't turn. Can you repair it?
Yes. On a top-loader, banging in the spin cycle usually means worn suspension rods or dampers. On front-loaders the cause is often worn drum bearings, which also get louder as the spin speeds up. A washer that has drifted out of level on a shifting slab can make the banging worse, so we check that too. Bearings are a longer job because the tub has to come apart. On an older washer, we compare that price to a new machine before starting.
Can you fix a dryer that runs but won't tumble?
Yes. A humming motor with a drum that won't turn usually points to a belt that broke or jumped its pulley. If the dryer won't do anything at all, we test the door switch and thermal fuse first. Worn rollers and idler pulleys often squeal for a while before they lock up. Belts, rollers and fuses are standard stock on the truck.
Do you repair induction cooktops and ranges?
Yes. Induction failures are usually electronic: the touch panel, the cooling fan, the power board or a sensor that watches coil temperature. Power surges from spring thunderstorms are a common trigger here. Many models show an error code first. Pass along that code with your model number when you phone, and the likely part can often come with the technician on the first visit.
Is that what yours is doing?
8 questions · answered here
Repair or replace?
How long each appliance tends to last, and a plain rule for deciding when a new one beats a repair.
Is my refrigerator worth repairing?
Usually. Thermostats, fans, control boards and defrost parts are all sensible repairs. As a guide, once the repair approaches half what a comparable new fridge costs and yours is well along in its expected lifespan, buying new is the better deal. The exception is built-in and panel-ready refrigerators, where repair nearly always wins. A garage fridge that has struggled through several summers deserves a hard look, because the heat wears down the compressor.
How long should a dishwasher last, and is mine worth fixing?
Most last around nine or ten years. Until then, a pump, door springs, latch, water valve or heater is worth replacing. After that, a leaking tub usually means it's time for a new one, and a dead control board is worth it only on a better-built machine. San Antonio water is hard, so scale on spray arms, inlet screens and the heater can shorten a dishwasher's life if the hardness setting and rinse aid are not right. If you have a water softener, the setting should be changed to match.
Should I repair my dryer?
Nearly always. Dryers are simple, and their wear parts, such as belts, rollers, fuses, heating elements and igniters, don't cost much. Replacement is the better call once rust has eaten through the drum, or if a very old dryer loses its main board. And if the vent is clogged, a brand-new dryer will run into the same trouble the old one did.
How long should a washer last before I replace it?
Expect around ten years, less in a busy household running a load or two every day. Swapping a lid switch, belt, door lock, drain pump or water valve is everyday work and worth doing. On an older front-loader, a cracked outer tub or worn-out bearings usually means it's time to shop for a new washer.
Should I repair my oven or range?
Most of the time, yes. A range usually gives 13 to 15 years of service, and its wear parts, igniters, bake elements, oven sensors and switches among them, are inexpensive. A gas range tends to outlast its control board, so a new board in a range that's otherwise sound is a good use of money. Pro-style and dual-fuel ranges are nearly always worth repairing. Ranges converted to propane in Hill Country homes are fixable too, as long as we know about the conversion.
Over-the-range microwave: repair it or replace it?
Repair makes more sense here than with a countertop model. It also serves as your range hood and hangs under the cabinets, so replacing it means paying for both the new unit and the installation. A failed fan, diode, switch or magnetron is usually the cheaper fix. Expect roughly nine years of service. With a countertop microwave that won't heat, buying a new one is often cheaper.
Is my freezer worth fixing?
Chest and upright freezers are built to run for many years. At almost any age, a failed thermostat, defrost part, fan or door gasket is worth fixing. The usual exception is a dead compressor in an older freezer, which is more likely if it has spent years in a hot garage. While you wait for us, leave the lid or door shut. A packed freezer holds its cold longer than a sparse one, so resist the urge to unload it.
Should I fix my wine cooler or buy a new one?
A built-in or dual-zone unit is usually worth fixing, since a replacement would have to fit that same cabinet opening. A small freestanding thermoelectric cooler is a different story, since a new Peltier module can cost close to what a whole new cooler does. On a compressor wine cooler, a failed fan, relay or thermostat is a worthwhile fix at almost any age.
Want us to look at yours and say honestly?
4 questions · answered here
Coverage across San Antonio
Where we go across Bexar and the neighboring counties, how routes are planned, and what hard water and summer heat do to your appliances.
Where around San Antonio do you provide service?
Ninety ZIP codes, grouped into 37 service areas. In Bexar County that takes in Downtown and King William, Alamo Heights, the Medical Center, Stone Oak, the East, West and South Sides, Fort Sam Houston and Lackland, plus Converse, Live Oak, Helotes, Alamo Ranch and rural South and East Bexar. Past the county line we reach Schertz, Cibolo, Seguin and Marion; New Braunfels, Canyon Lake, Bulverde and Garden Ridge; Boerne and Fair Oaks Ranch; Castroville, Hondo and Pipe Creek; La Vernia; and San Marcos. The service areas page lists every ZIP.
Why does hard water matter for my appliances?
Most San Antonio tap water comes from the Edwards Aquifer, which is limestone, so it carries a lot of dissolved minerals. Those minerals scale up washer inlet screens, ice maker fill valves, fridge water dispensers and dishwasher spray arms, and the buildup slowly restricts the water until the appliance acts broken. SAWS publishes hardness figures in its annual water quality report, and if you are on another utility or a private well, your water bill or a well test will tell you more. A softener helps, but it changes how much detergent you need and where a dishwasher's hardness setting belongs.
Why can't you give me an exact arrival time?
Our technicians cover a lot of ground on Loop 410, Loop 1604, I-10, I-35 and US-281, and traffic on those roads, plus construction and summer storms, makes exact times hard to promise. A repair can also take longer than expected once the appliance is opened. Our dispatcher sets a three-hour arrival window for you, and the technician phones if anything shifts.
Why is my garage fridge or freezer struggling?
Heat. Most refrigerators and freezers are designed for an indoor room, and a San Antonio garage in August can get much hotter than the outside air. The fridge can't dump heat quickly, so the compressor never cycles off, and a layer of dust and pet hair on the condenser makes that worse. During a hard freeze the opposite can happen and the freezer side can warm up. Clean coils and a bit of breathing room around the cabinet both help. Fridges rated for garage use handle the swings better, and a repair can't turn a standard model into one.
90 ZIP codes across 37 areas in Bexar, Guadalupe, Comal, Kendall, Medina, Bandera, Wilson and Hays counties. Browse every area we serve to find your neighborhood.
Wondering if we reach your street?
15 questions · answered here
Your appliance
Questions San Antonio homeowners ask about specific machines, and what we usually find. A few turn out not to be faults.
Refrigerator
Refrigerator repair page →Food in the main compartment is warming up while the freezer side holds its chill. Is the compressor dead?
Usually not. A freezer that's still cold tells us the sealed system is doing its part. What has stopped is the flow of cold air into the fresh-food side. Most often the evaporator coil behind the freezer's back panel has frosted over, because the evaporator fan quit or a defrost heater, timer or defrost thermostat failed. Those are some of the more affordable refrigerator repairs, and they get mistaken for a compressor failure all the time.
What does a typical refrigerator repair involve?
It falls into two groups. The common, mid-priced group is fans, defrost parts, thermostats and control boards. Sealed-system jobs, such as fixing a refrigerant leak, clearing a restriction or putting in a new compressor, cost far more, and on an older budget fridge they often don't pay off. The diagnostic visit tells us which group yours is in, and you get the price before deciding.
Why does my garage refrigerator keep breaking down?
Because it was built for a kitchen, not a San Antonio garage. In July and August an attached garage gets far hotter than the outdoor temperature, and the fridge can't reject heat fast enough, so it runs nonstop and the condenser coils load up with dust. On those rare hard-freeze nights, a fridge with only one thermostat can sense the cold and quit running, and the freezer side then warms up. That kind of temperature swing is what garage-rated models are designed for. A repair can't convert a standard fridge into one.
Washer
Washer repair page →My washer stopped spinning. Is the motor shot?
Probably not. A washer won't spin with water still sitting in the drum, so the real problem is usually the drain. Start with the drain pump filter. A sock, a hair tie or a few coins there are much more likely than a bad motor or board. Once the drain checks out, we test the lid or door lock, then move on to the coupler or belt.
Doesn't the error code point straight to the part that needs replacing?
Not on its own. A code reports what the washer noticed, not why it happened. A slow-fill code only means water didn't arrive on time. The cause could be low water pressure, an inlet screen scaled up by San Antonio's hard water (a common problem), a worn water valve or a bad level sensor. So we test the possible causes before ordering anything.
Why does my front-load washer smell?
Water is sitting where it shouldn't, in the sump, the pump filter or the drain hose, and a film builds up on the rubber door boot. Front-loaders are prone to this because the door boot stays wet between loads, and a warm, humid laundry room next to the garage makes it worse. Wipe the boot, leave the door cracked after each load and clean the filter. If the odor keeps returning, have the drain checked before it turns into a bigger problem.
Dryer
Dryer repair page →Why did the new heating element in my dryer burn out too?
Because the vent was the actual problem. A dryer has to move a lot of air. A clogged or crushed vent makes the element overheat, so its safety cutoff keeps tripping until the element burns out. A new element on a vent that's still blocked will burn out just like the old one. We test how much air actually moves, and when the run is too long for that dryer to push through, we say so.
Are dryer repairs expensive?
Usually not. Belts, idler pulleys, rollers, thermal fuses, heating elements and igniters are all fairly cheap, and fitting them is straightforward work. The costly situation is a healthy dryer on a bad vent. Cleaning or rerouting the duct is a separate job, and replacing dryer parts won't fix it.
Why do my loads take two or three dryer cycles?
Almost always the vent. Many San Antonio homes, single-story houses with an interior laundry closet in particular, run the duct up through the attic and out a cap on the roof. That is a long, hot run, and lint settles in it fast. Add a crushed foil transition duct behind the dryer and a wad of lint at the first elbow, and very little air ever reaches outside. The heater can work fine and the clothes still come out damp. A clogged attic vent is a fire hazard too, so don't put off fixing it.
Dishwasher
Dishwasher repair page →My dishes come out wet. Is the heater broken?
Not if you have a Bosch, Miele, ASKO or a similar European dishwasher. Many of them have no exposed heating element. They dry by condensation on the cooler stainless tub, so plastics often come out damp. They're built to work that way, so it isn't a fault.
What causes a white film on my glasses?
In San Antonio it is usually hard-water scale. The Edwards Aquifer is limestone, so tap water carries a lot of calcium and magnesium, and they leave a cloudy film on glassware and crust on the spray arms. Using rinse aid and setting the water hardness correctly makes a big difference. If your home has a water softener, the opposite can happen: too much detergent in soft water etches glass, which looks similar but won't wipe off. We check your water and set the hardness option to match if your model has one.
Why isn't the top rack getting clean?
Look at what feeds water up there. The upper rack only comes clean if water gets up to its spray arm, so a stuck diverter, a clogged feed tube or scale in that arm's jets causes exactly this, even though the bottom rack washes fine. Before we suspect the pump, we spin the spray arms, clean out the jets and check the diverter.
The element looks normal, but my oven doesn't get hot enough.
Two things to check first. One is calibration. The oven may be holding a steady temperature, just not the one on the display, and on many models you correct that offset in the settings rather than with a part. The other is the door. Tired hinges or a worn gasket bleed off heat faster than the element can keep up, which looks exactly like a heating failure.
What does an oven repair usually involve?
Usually the fix is an igniter, a switch, a temperature sensor, or a bake or broil element. The parts don't cost much and the labor is simple. Wall ovens cost more in labor because the unit has to be pulled from the cabinet carefully, and because any new wall oven must slot into the opening your cabinets already have, repair stays the sensible choice years after you'd give up on a freestanding range. Ovens get their hardest workout here from Thanksgiving through New Year's, so a weak igniter is worth fixing before the holidays.
I smell gas near my oven. What should I do?
Switch the oven off and don't use it again until it's checked. With a strong smell, get everyone out of the house, leave the light switches alone, and once outside call CPS Energy, your propane supplier or 911. Then call us. We close the appliance's gas valve and check every fitting with a gas detector. When the leak is in the home's gas piping and not the oven, we keep the valve closed and let you know.
Your appliance not listed here? Try the complete list of appliances we repair, where each one has its own page of common faults.
Seeing a problem that isn't here?
2 questions · answered here
Condos, gates, gas and refrigerant
High-rise and HOA rules, gate access, building paperwork, gas lines and refrigerant. The things a property manager asks about first.
Can you work in my condo, high-rise or gated community?
Yes. Downtown and Pearl high-rises often set rules for contractors, such as paperwork on file or a reserved service elevator or loading dock, and gated communities like The Dominion need gate access arranged in advance. Tell us what your building or HOA requires when you book. Sorting out paperwork before the visit keeps the technician from waiting in a lobby or at a guard shack.
How do you handle gas lines and refrigerant?
By the book. Before we touch any gas appliance, natural gas or propane, its supply valve gets closed, and every fitting we loosened is leak-checked before you use the appliance again. We handle all sealed-system refrigeration work under EPA Section 608 refrigerant rules.
Need paperwork or gate access set up first?
6 questions · answered here
What it costs, scheduling and warranty
Why we don't publish prices, what drives the cost of a repair, how the diagnostic fee is credited, and what the warranty covers.
A single symptom can trace back to very different failures. An ice maker that has stopped could have a scaled-up inlet valve, a frozen fill tube or a dead control module. One is a modest repair, another is not, and no one can tell which over the phone. That is why we don't publish a price list. You hear what the diagnostic visit costs before anyone is sent, and the repair price is settled before any work starts.
Every appliance page ranks that machine's common faults from the cheapest to the most expensive, so once the technician names the failed part you can see roughly where yours lands.
- Refrigerator repair cost
- Washer repair cost
- Dryer repair cost
- Dishwasher repair cost
- Oven repair cost
- Microwave repair cost
- Freezer repair cost
- Cooktop repair cost
- Ice Maker repair cost
- Wine Cooler repair cost
- Range & Stove repair cost
- Small parts that wear out. The cheapest band, and the one most repairs land in. Parts such as fuses, seals, sensors, igniters and belts are designed to fail ahead of the costly components, so the part is inexpensive and the work goes fast.
- Motors, pumps and moving parts. The middle of the range. These parts cost more, and reaching them often involves taking off a panel or pulling the drum, so labor is a bigger share of the bill than the part alone would suggest.
- Boards and electronics. The costly band, so it is worth pausing to think before you approve it. The board itself is most of the cost, and installing it rarely takes long. Here, on an older unit, buying new can be the better move, and if so the technician says it outright.
- Sealed cooling system. The costliest and the rarest. Fixing a leak or a compressor involves recovering refrigerant, brazing joints, pulling a vacuum and recharging the system, all under EPA Section 608 rules. On an older, ordinary fridge this repair often is not worth it, and we say so up front, before you spend a cent.
How quickly can you get a technician out?
A real person answers at any hour, and the dispatcher books the earliest slot the schedule actually has open, with a three-hour arrival window. San Antonio is a big, spread-out city, so we route by side of town: the north side along 1604 and 281, the west side along Culebra, Potranco and Bandera Road, and the east and south sides off I-35, I-10 and I-37. If a technician is already working near you, you may get in sooner. A call that comes in late at night is normally booked for the first opening the next morning.
How does pricing work?
The visit has a diagnostic fee, and it's credited to the repair if you decide to proceed. The technician tests the appliance first, finds what failed, and then gives you one price that covers both the part and the labor. The repair waits for your okay on that figure, and the figure doesn't move once the work begins.
Does someone really answer the phone at any hour? Is there a night rate?
Yes to the first, no to the second. Someone answers every hour of every day, holidays included, and the rate is the same at midnight on a Saturday as it is on a Wednesday afternoon. Fewer technicians work through the night, so a call that comes in late usually gets one of the first slots the next morning. If you have a gas smell, water running onto the floor, or a freezer full of food warming up in a July heat wave, say so on the call and we will tell you honestly how quickly we can help.
What does your warranty cover?
Every part we install carries a 90-day warranty; the labor on that job carries 30 days. Should the same problem return within that period, we come back with no second diagnostic fee. The warranty applies to the repair we did. When some other part of the appliance breaks later on, we'll tell you straight that it's a new fault, not a warranty claim.
Will you say so if my appliance isn't worth fixing?
Yes, and it comes up more often than you might expect. A useful rule of thumb: when a repair costs close to half of what a comparable new model would, and yours is about two-thirds through its normal life, replacing it usually wins. The exception is built-in and panel-ready appliances. Swapping one out can mean cabinet work, so repairing it stays the better choice for much longer.
What information should I have when I call?
The brand and model number, plus a quick description of what the appliance does or fails to do. The model sticker is usually on the inside of the door or the frame, behind the lower kick plate, or on the back panel. A photo of it from your phone works perfectly. If we have the model number, the technician can carry the parts that commonly fail on it, which gives you the best chance of a one-visit repair.
Every completed repair carries the 90-Day Parts & 30-Day Labor Warranty. The contact page lays out how a visit goes, from the first call to the finished repair.
Want to book a time?
5 questions · answered here
In your home
Who has to be there, how we protect floors, access paperwork, and having a second appliance looked at during the same visit.
Does someone have to be home while the technician is there?
An adult, 18 or up, needs to be home to open the door for our technician and okay the price before work begins. If you're a renter or you manage a property for an owner, we need written approval from the person paying before the visit. That gets settled ahead of time, not on the doorstep.
Will the technician protect my floors?
Yes, on every visit, at no charge. Technicians carry floor runners and appliance slides. We close the water supply and drain the line before pulling out a dishwasher, or any refrigerator plumbed to a water line. Before moving a gas appliance, its gas valve is closed.
Our HOA or building has rules for contractors.
That is common with condo towers downtown, managed apartment buildings and some HOA communities. When you book, tell us what the building or community requires, and we confirm what we can supply ahead of the visit. We can also work around a reserved service elevator, a loading dock slot or gate access so the technician isn't held up getting in.
Can you check a second appliance on the same visit?
Yes, just mention it when you book. Looking at another appliance on the same trip doesn't add a second trip charge. Many San Antonio homes run a kitchen refrigerator plus a backup fridge or chest freezer in the garage, and that garage unit is often the one quietly struggling in the heat.
Will you repair an appliance someone else installed?
Almost always. We repair appliances, we don't sell them, so where it came from doesn't matter to us. What we do look for is a previous repair that used the wrong part, a very common reason the same problem keeps coming back.
Tight laundry closet or a fridge out in the garage?
5 questions · answered in context
In a commercial kitchen
How fast a down kitchen gets seen, timing around your rush, the brands we service, and records for the health inspector.
- How quickly can you reach a restaurant or bar?Commercial
- Can you work around our service hours?Commercial
- What commercial equipment brands do you service?Commercial
- Why does our ice machine or cooler keep failing?Commercial
- Do we get a written record of the visit?Commercial
Ice machine or reach-in giving you trouble?
Still wondering?
Ask us the unusual one
Some questions don't fit a list. An older model whose parts are getting scarce, a range converted to propane, a freezer wedged into a hot garage corner. Call and describe it. Most of these get sorted out in a few minutes.