Jump to main content

Washer repair in San Antonio, fixed at your place.

Front-load or top-load, garage or hallway closet, here is how our technicians track down what's wrong with a washer and what San Antonio's water does to it.

Phones staffed 24/7Three-hour arrival window90-day parts warranty

Diagnosis
The failed part is found before any price
Approval
No work begins without your okay
Hours
Calls answered day and night
Warranty
Parts 90 days · labor 30 days

Book online

Send the basics. A dispatcher calls you back.

  1. 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
  2. 2Pick up when we callWe confirm the address and set a three-hour arrival window.
  3. 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.

Would rather explain it out loud? Call us any hour, any day.

Schedule a repair

Step 1 of 2 · Appliance and area

Step 1 of 2

Appliance and area

Which appliance?

Appliance

Where in the San Antonio area?

Booking costs nothing, and we never ask for a card.

Prefer to call? (210) 939-3313

1–2 hours
Typical time on site
30
Washer faults we fix
19
Brands we service
24/7
Phones answered

Washer problems

What is wrong with your washer?

Pick a symptom for the usual causes and the fix a technician makes.

  • Washer won't spin the clothesThe tub goes through the motions but the clothes come out soaked. Sometimes you hear the motor hum, or the drum starts to turn and quits. Most of the time the washer is refusing to spin on purpose because something upstream, usually drainage or the lid, didn't check out.

    Typical culprits

    • Water still in the tub, so the control won't allow a spin
    • Door lock or lid switch not telling the control it's shut
    • Drive belt stretched, slipping or broken
    • Motor coupler or clutch worn out on a top-loader
    • Motor or motor control board not delivering power
    • A single heavy item throwing the load off balance

    How the technician handles it

    First we make sure the tub drains, since that is the most common reason for a blocked spin. Then we check the lid or door circuit, the belt and coupler, and the motor and its control in that order. Once the bad part is replaced, we run a full spin with a wet load before calling it done.

  • Washer won't drain, water sitting in the tubThe cycle ends with a tub full of gray water, or the machine stalls partway through. It is a messy problem but usually a mechanical one. The water has to get through the pump, the drain hose and the house standpipe, and any of the three can hold it up.

    Typical culprits

    • Socks, coins or hair ties jammed in the pump or coin trap
    • Drain hose kinked when the washer got shoved back against the wall
    • Drain pump motor burnt out or seized
    • Standpipe or laundry drain line clogged with lint
    • Pressure switch hose blocked, so the level reads wrong

    How the technician handles it

    We bail or drain the tub safely, then open the pump and trap to pull out whatever is stuck. If the pump is clear, we test it for power and resistance and check the hose and standpipe. A failed pump gets replaced, and we finish by running a drain and spin to confirm the water leaves at full speed.

  • Washer making loud noisesGrinding, banging, scraping or a steady roar all mean different things. The kind of noise and the point in the cycle where you hear it tell a technician most of the story before any panel is removed.

    Typical culprits

    • Worn tub bearings on a front-loader, loudest at high spin
    • Coin, key or bra wire trapped between drum and tub
    • Tired suspension springs or dampers letting the tub knock
    • Debris rattling in the drain pump impeller
    • Washer not level, or a lopsided load

    How the technician handles it

    We run the washer through each stage and listen for where the noise starts. A rattle during draining points to the pump, a scrape during wash points to something between the drums, and a roar on spin points to bearings. We remove debris on the spot and quote any part replacement before doing it.

  • Washer won't start at allYou load it, pick a cycle and press start, and nothing happens, or the display lights up but the drum never moves. Before assuming the worst, it helps to know that a lot of no-start calls come down to a lock or a setting.

    Typical culprits

    • Front-load door lock not engaging
    • Top-load lid switch broken or out of alignment
    • Control lock or child lock turned on
    • Thermal fuse or board fuse blown
    • User interface board or start button not reacting
    • Outlet, GFCI or breaker tripped

    How the technician handles it

    After confirming outlet power and ruling out control lock, we check the lid switch or door lock, since the washer won't do anything until it reads that as closed. From there we check fuses and the interface and main boards. Nothing gets swapped until you've heard the diagnosis and the price.

  • Washer leaking water on the floorA puddle in front of a front-loader, a wet spot behind a top-loader or water creeping into the garage all deserve quick attention. Where the water shows up, and whether it leaks during fill, wash or drain, narrows down the source fast.

    Typical culprits

    • Fill hose split or its rubber washer cracked
    • Front-load door boot torn or folded wrong
    • Drain pump seal or hose clamp leaking
    • Tub seal failed under the drum
    • Too much detergent foaming over the top
    • Hose split by a freeze in a garage or exterior-wall laundry room

    How the technician handles it

    We dry the area, run a short cycle with the panels off and watch for the first drip. Hoses, clamps and pump seals can often be fixed on the first visit if the part is on the van; boot seals sometimes need ordering. Because a failed tub seal takes more labor, we weigh the repair against the machine's age with you before you decide.

  • Washer won't fill with waterThe washer clicks, maybe hums, but no water comes in, or it trickles in so slowly that the cycle times out. San Antonio's hard water makes this a common call, since mineral grit gathers on the little screens at the hose connections.

    Typical culprits

    • Inlet valve screens clogged with scale or sediment
    • Inlet valve solenoid coil burnt out
    • Supply hose kinked or frozen
    • Water level pressure switch faulty
    • Faucets behind the washer partly closed or low house pressure

    How the technician handles it

    We shut the water off, pull the hoses and check the screens, which are often caked with mineral grit. When the screens look clean, we test the level switch and each inlet valve coil. A new valve usually solves it, and we check the hoses for age and kinks while they're off.

  • Front-load washer door won't lockA front-loader won't fill until the door locks, so a lock fault stops the cycle before it begins. You may see the lock light flash, hear repeated clicking, or get a door code on the display.

    Typical culprits

    • Lock motor or solenoid failed
    • Strike hook on the door bent or snapped
    • Sagging door hinge so the latch hook can't reach the lock
    • Wiring to the lock chafed through where the boot flexes
    • Lock switch not reporting back to the control

    How the technician handles it

    We look at the strike hook and hinge first, since a sagging door is an easy fix. Then we test the lock assembly and trace its wiring through the boot area. A new lock or a repaired harness usually brings it back, and we test several lock and unlock cycles before leaving.

  • Washer shaking and walking across the floorA washer that bucks hard on spin or creeps away from the wall is hard on itself and on the floor. On a second-floor laundry closet it can shake the whole room.

    Typical culprits

    • Shock absorbers or dampers worn out
    • Suspension rods or springs broken
    • Leveling feet uneven or not locked
    • Shipping bolts left in a newly installed washer
    • Floor flexing under the machine
    • Loads that bunch, like a single comforter or rug

    How the technician handles it

    We check level and leveling locks, look for shipping bolts on newer machines, and then push and release the tub to test the suspension. Worn shocks or rods get replaced as a set. At the end we spin a full test load so you can see the change for yourself.

  • Washer flashing an error codeA code tells you which system the washer is unhappy with, not exactly which part failed. A drain code, for example, can mean a clogged pump or a bad pressure sensor. Write the code down before you reset anything.

    Typical culprits

    • Drain code from a blocked pump, hose or standpipe
    • Door or lid code from a failed lock or switch
    • Motor error from a worn motor or failing hall sensor
    • Unbalance code from a lopsided load or worn suspension
    • Water level error caused by a bad pressure sensor
    • Fill code from clogged inlet screens

    How the technician handles it

    We pull the stored codes, look up what that model means by each one, and test the circuit the code points to. That keeps us from replacing a board when the problem is a clogged hose. You get a clear answer on which part failed before anything is ordered.

  • Top-load washer not agitatingThe tub fills, but the agitator sits still or barely twitches. On direct-drive machines it is often a small plastic part such as the motor coupler or agitator dogs. On newer high-efficiency top-loaders, the shifter or gearcase is more likely.

    Typical culprits

    • Agitator dogs or cogs worn smooth
    • Motor coupler broken
    • Drive belt slipping
    • Shift actuator or gearcase failure
    • Lid switch telling the control the lid is still up

    How the technician handles it

    After pulling the agitator cap to check the dogs, we inspect the coupler and belt. If those are fine, we test the shifter and listen to the gearcase. Agitator dogs and couplers are inexpensive parts, while a gearcase is a bigger job we'll talk through with you first.

  • Washer smells musty or like mildewThat sour smell usually comes from detergent residue and lint that stay damp inside the machine. Front-loaders are the worst for it because the door seal holds water in its folds.

    Typical culprits

    • Mildew trapped in the door boot's folds
    • Residue left by too much soap or a non-HE detergent
    • Stagnant water in the drain pump filter
    • Door kept shut between loads
    • Drain hose stuffed too deep in the standpipe and siphoning water back

    How the technician handles it

    We clean the boot and pump filter, check the drain hose height and look for residue in the dispenser. Then we walk you through a cleaning cycle and the detergent dose that suits your water. If you have a softener, that dose is often lower than people expect.

  • Clothes still dirty after washingStains left behind, detergent streaks or a dingy look all point to too little water, too little movement or a dosing problem. It is rarely a single broken part, so the diagnosis starts with how the washer is loaded and fed.

    Typical culprits

    • Drum packed too full for clothes to move
    • Inlet valve letting in too little water
    • Detergent dispenser not flushing
    • Internal heater not warming water on models that have one
    • Worn agitator dogs leaving the top agitator barely moving
    • Hard water reducing how well detergent works

    How the technician handles it

    We watch a fill and wash cycle to see how much water comes in and how the load moves. Then we check the dispenser, the heater if there is one, and the agitator drive. If changing the dose or how you load the machine will fix it, we tell you so and don't sell you a part.

  • Washer door stuck shut after the cycleClothes are locked inside and the door won't release. As long as the washer thinks the drum holds water or is still spinning, it keeps the door locked, so the real problem often lies elsewhere.

    Typical culprits

    • Drain fault leaving water sitting in the drum
    • Lock mechanism jammed in the locked position
    • Control board not sending the unlock signal
    • Door handle or latch hook broken

    How the technician handles it

    We drain the drum through the pump filter if needed, then release the door using the manual release where the model has one. Once it's open, we fix whatever kept it locked, whether that's the drain, the lock or the control signal.

  • Front-load door seal torn or leakingThe rubber boot between the door and the drum takes a beating from zippers, coins and the occasional nail left in a pocket. A small tear leaks on every wash and can let water reach the motor and controls below.

    Typical culprits

    • Sharp objects caught in the boot fold
    • Rubber hardened and cracked with age
    • Mildew weakening the folds
    • Boot clamp spring loose or slipped
    • Bleach or harsh cleaners breaking down the rubber

    How the technician handles it

    We fit the new boot with new clamps, drain holes facing down, and we check the drum lip for burrs that could slice it. A leak test with a full wash confirms the seal before we leave.

  • Washer roaring or rumbling on spinWorn tub bearings classically make a low roar that grows louder as the spin picks up speed. It usually starts quietly and gets worse over a few months.

    Typical culprits

    • Tub seal leaking water into the bearings
    • Bearings worn out after years of high-speed spins
    • Overloading straining the shaft
    • Corroded spider arm loosening the drum
    • Rust from water damage inside the bearing housing

    How the technician handles it

    We confirm worn bearings by turning the drum by hand, feeling for play and looking for rust streaks. Replacing bearings and seals means pulling the tub apart, so we go over the labor involved and the shape the rest of the washer is in. Some models only sell the bearings with a whole new outer tub, and we'll tell you that before you choose.

  • Washer shocks or suspension worn outShocks and springs let the tub move during spin without slamming the cabinet. Once they wear out, the tub bangs on every spin and the machine starts walking.

    Typical culprits

    • Shock absorbers lost their damping
    • Suspension springs stretched
    • Snubber pad worn on some top-loaders
    • Mounting bushings cracked
    • Suspension rods worn at the ball ends

    How the technician handles it

    We press down on the tub and watch how it rebounds, then inspect each shock, spring and rod. Worn parts get replaced in sets so the tub hangs evenly, and we finish with a test spin on a full load.

Show 14 more washer problems
  • Broken drum support (spider arm)The spider arm is the three-pronged bracket that holds a front-loader's drum to its shaft. When an arm corrodes and cracks, the drum wobbles and clanks, and it can scrape the outer tub.

    Typical culprits

    • Aluminum arm corroded by detergent and fabric softener
    • Overloading and repeated unbalanced spins
    • Seal leaking water down into the arm
    • Age, with salts from hard water speeding up corrosion

    How the technician handles it

    We confirm the break by checking drum play and looking through the rear of the tub. A spider arm repair is a full teardown, often with new bearings and seals, so we'll talk through cost against replacing the washer before ordering anything.

  • Washer drive belt broken or slippingOn belt-drive washers, the motor turns the drum through a belt. When it slips, the drum spins slowly or not at all, and you may smell burning rubber.

    Typical culprits

    • Belt stretched and slipping
    • Drum or motor pulley damaged
    • Overloading the drum
    • Tensioner or idler worn
    • Belt cracked from age and heat

    How the technician handles it

    We pull the back panel, inspect the belt and pulleys and check the tensioner. A new belt goes on with the pulleys checked for wear, and we test wash and spin speeds before closing it up.

  • Washer drain pump not workingA failed pump leaves water in the tub, and the washer halts with a drain error code. A buzzing pump that won't move water has often been jammed by debris for a while.

    Typical culprits

    • Impeller blades cracked or broken
    • Pump motor winding open
    • Debris jamming the impeller
    • Control never sending voltage to the drain pump
    • Pump housing cracked and leaking

    How the technician handles it

    We drain the tub, clear the trap, and test the pump for voltage and resistance. If the pump is dead and power is reaching it, we install a new one and run a drain test. If no power arrives, we trace the wiring and control instead.

  • Washer drain filter cloggedOn many front-loaders, a small filter sits behind a panel down at the bottom front. It catches lint, coins and hair before they reach the pump, and when it fills up, drainage slows to a crawl.

    Typical culprits

    • Lint and pet hair packed into the filter
    • Coins, buttons or hair clips trapped
    • Filter not cleaned in months
    • Detergent sludge building up around the filter
    • Filter seal damaged so it won't close tight

    How the technician handles it

    We drain the line into a pan, clean the filter and the housing, and check the impeller behind it. If the seal is worn, we replace it. We'll also show you how to open it yourself and how often it is worth doing.

  • Washer water inlet valve failedThe inlet valve opens and closes to let hot and cold water in. A failed valve can stop water completely, let in only one temperature, or leak in slowly even when the washer is off.

    Typical culprits

    • Solenoid coil burnt out
    • Valve screens blocked with mineral scale
    • Valve diaphragm worn, allowing a slow leak
    • Wiring connector loose
    • Valve body cracked from a freeze

    How the technician handles it

    We test each coil and inspect the screens and body. A new valve goes in with fresh hose washers, and we check that both hot and cold fill properly. If your water is hard, we'll mention how often to check the screens.

  • Top-load lid switch not workingA top-loader won't spin, and newer ones won't start, unless the lid switch reports closed. A broken switch can make a healthy washer seem dead.

    Typical culprits

    • Switch actuator broken off the lid
    • Switch contacts burnt
    • Failed lid lock motor on a late-model top-loader
    • Wiring broken where the lid hinges
    • Lid hinge bent so the actuator misses

    How the technician handles it

    We check the actuator and alignment, test the switch and lid lock electrically and inspect the wiring at the hinge. A new switch or lock assembly usually fixes it, and it's often on the van.

  • Washer control board problemThe control board runs the timer, the valves, the motor and the lock. A failing board can show odd behavior: random stops, skipped steps, a blank display or a washer that won't respond.

    Typical culprits

    • Surge from a spring storm or outage
    • Water leaking onto the board
    • Burnt relay or circuit trace
    • Failed motor control section on inverter models
    • Loose or corroded harness connector

    How the technician handles it

    We test the parts the board controls before blaming the board, since a shorted valve or pump can take a board out with it. For a bad board, we track down what damaged it, put in a new one and run a complete cycle to verify.

  • Washer motor not runningWhen the washer fills and drains yet the drum never moves, look to the motor or the parts that drive it. Sometimes the motor hums, sometimes it is silent.

    Typical culprits

    • Motor windings burnt out
    • Hall sensor or tach failure
    • Motor capacitor failed on older top-loaders
    • Wiring to the motor broken
    • Motor control board not driving the motor

    How the technician handles it

    We test the motor windings, sensor and wiring, and check the control's output. Motors are expensive, so we confirm the fault twice and lay out the repair against the washer's age before you approve.

  • Detergent left in the dispenser drawerDetergent sitting in the drawer after the cycle means the water meant to flush it didn't come in, or came in too weakly. Over time this can leave clothes underwashed.

    Typical culprits

    • Dispenser drawer clogged with dried detergent
    • Low water pressure into the dispenser
    • Diverter valve or dispenser motor failed
    • Detergent poured into the wrong compartment
    • Scale in the dispenser jets from hard water

    How the technician handles it

    We pull and clean the drawer and the housing jets, check water pressure at the valve and test the diverter or dispenser motor. Most of these are fixed with a cleaning and a valve check.

  • Fabric softener not dispensingThe softener cup is still full after the rinse, or the softener went in too early and left spots. Softener is thick, so small clogs make a big difference.

    Typical culprits

    • Siphon tube in the softener cup clogged
    • Softener too thick or the cup overfilled
    • Dispenser not getting water at rinse
    • Agitator softener cup cracked
    • Diverter not switching to the softener path

    How the technician handles it

    We clean the siphon and cup, check the rinse fill and test the diverter. If the agitator cup is cracked, we replace it. Diluting thick softener a little often keeps the problem from coming back.

  • Washer stops in the middle of a cycleThe washer stops partway through and either sits there or shows an error. This is usually the control quitting because a step took too long or something reported wrong.

    Typical culprits

    • Water draining so slowly that the control gives up
    • Pressure switch reporting wrong levels
    • Motor overheating and shutting down
    • Door lock losing contact for a moment
    • Slow fill from clogged inlet screens

    How the technician handles it

    We run a monitored cycle and check stored codes to see where it stops. Then we test the drain, the level sensor, the motor and the lock. Once the cause is fixed, we run a complete cycle start to finish.

  • Wash cycle takes much longer than it used toModern washers add time when they detect a slow fill, a slow drain or an unbalanced load. A cycle that has grown by half an hour is a sign, not a quirk.

    Typical culprits

    • Slow fill from clogged inlet screens
    • Slow drain from a partly blocked pump
    • Repeated balancing attempts before spin
    • Water heater element slow to warm on heated models
    • Excess suds making the washer add rinses

    How the technician handles it

    We time the fill and drain, check the screens and pump and watch the balance routine. Clearing the slow step usually brings the cycle back to normal without any new parts.

  • Washer only uses cold waterWarm and hot cycles feel cold, or the washer fills with cold water no matter the setting. Modern washers also mix in cold water on purpose, so it helps to check what the cycle is supposed to do.

    Typical culprits

    • Hot side of the inlet valve failed
    • Hot and cold hoses swapped
    • Hot faucet closed or the water heater far from the laundry room
    • Temperature sensor or thermistor faulty
    • Hot inlet screen clogged with scale

    How the technician handles it

    We check the hot supply at the faucet, then the hot screen and coil. We test the temperature sensor and confirm the hose layout. In a garage laundry room far from the water heater, running the hot tap first can make a difference, and we'll tell you if that's all it is.

  • Washer overflowing with sudsFoam pouring out of the door or the dispenser almost always comes from detergent. HE washers use so little water that any extra detergent foams up, and softened water makes it foam faster still.

    Typical culprits

    • Regular detergent used in an HE washer
    • Too much detergent per load
    • Softened water needing much less detergent
    • Slow drain keeping suds in the tub
    • Detergent residue built up from past loads

    How the technician handles it

    To clear the suds we run rinse cycles, then check the drain and look for detergent buildup. Then we set a detergent amount that fits your water. With a softener, many households can cut their dose sharply.

Brands

Washer brands we repair

All brands →
  • Samsung logo
  • LG logo
  • Whirlpool logo
  • GE Appliances logo
  • Maytag logo
  • Bosch logo
  • Frigidaire logo
  • Kenmore logo
  • Amana logo
  • Electrolux logo
  • Miele logo
  • Admiral logo
  • ASKO logo
  • Avanti logo
  • Blomberg logo
  • Fisher & Paykel logo
  • Hotpoint logo
  • Roper logo
  • Speed Queen logo

From our technicians

Washer repair notes for San Antonio homes

Most washers that reach us aren't really dead. They are protecting themselves. A modern washer checks a list of things before every step: is the lid or door locked, did the water reach the right level, did the drum empty, is the load balanced. If one of those checks fails, the machine stops or skips the spin, and to the person standing in front of it, it looks broken.

So a good diagnosis starts with what the washer was trying to do when it quit, not with the part that looks guilty. Wet clothes sound like a motor problem, but usually the drum never drained and the control refused to spin.

San Antonio adds its own twist. SAWS water comes mostly from the Edwards Aquifer, which runs through limestone, so it is hard, and hard water leaves scale and grit in valves, screens and dispensers. Many laundry rooms here are off the garage, where summer heat bakes the rubber and a hard freeze can split a hose overnight. Those conditions show up in our repair notes again and again.

The order we check a washer in

We rule out the common, inexpensive causes before moving to the costly ones. Power and settings come first: the outlet, any GFCI in the garage, the breaker and the control lock. Then the door or lid circuit, because a washer that can't confirm it is closed won't fill, agitate or spin. After that we follow the water: the inlet screens and valve on the way in, and the pump, coin trap, hose and standpipe on the way out.

Only when the water path checks out do we move to the drive: belt, coupler, shifter, motor and the board that powers them. Bearings and suspension come last, and we judge them by sound and feel during a spin. Working in this order means we rarely replace something that wasn't actually broken, and the quote you get reflects the real fault.

Hard water, softeners and what they do inside the machine

Hard water first shows up in the little mesh screens at the spot where the fill hoses attach to the washer. Grit and mineral flakes build up there, slowing the fill until the washer shows a fill error or drags the cycle out. It also coats dispenser jets, so detergent sits in the drawer. On machines with a built-in heater, scale on the element slows warming, and sanitize cycles get longer.

A whole-house softener fixes much of that but changes the detergent dose. Softened water suds easily, and in a low-water HE washer a normal dose can foam over and trigger extra rinses or a suds error. Start with the smallest dose the label allows. On a Hill Country well, a sulfur or musty smell may come from the water rather than the washer, and we'll tell you which.

Garage and closet laundry rooms, heat and freezes

Many San Antonio washers live in the garage or a closet off the hallway. Garage machines bake through summer, which dries out hoses, door boots and drain lines. Closet installs are tight, so hoses kink when the washer is pushed back, and an upstairs front-loader can shake the room if it isn't level.

Hard freezes are rare here, but the February 2021 storm showed what they can do. Water left in the inlet valve, hoses or pump can freeze and crack them, and the leak only shows up on the next load. If a hard freeze is forecast and the washer sits in an unheated garage or on an exterior wall, shut the faucets off and disconnect the hoses if you can. Afterward, run a short cycle and watch the floor.

The problem people misread most

Clothes come out wet, so people assume the washer won't spin. But in most of those cases the washer is fine. It couldn't drain fast enough, so it never got the signal to spin. Usually a hair tie or sock has lodged in the pump, lint has packed the coin trap, or the drain hose has been pushed too deep into the standpipe. The second most misread problem is a door that won't open: the lock is working exactly as designed because there is still water in the drum.

On repair-or-replace: hoses, pumps, valves, lid switches, door locks, belts and shocks are worth fixing on almost any washer. Bearings, spider arms and motors are the big jobs, and on an older or budget machine we'll lay out the trade-off and let you decide. A rusted cabinet, a cracked outer tub or a second major failure usually tips it toward replacing.

What you can do safely, and what to leave for us

Unplug the washer before doing anything beyond pressing buttons, and close the faucets if you're chasing a leak. Homeowners can safely empty a front-loader's pump filter (keep towels and a shallow pan handy), wipe out the door boot folds, prop the door open between loads, clean the dispenser and swap out hoses that are cracked or bulging. Braided stainless hoses are worth the upgrade.

Leave pumps, valves, locks and boards to us. Within your three-hour window the technician arrives, asks what you saw and heard, runs the washer and tests the suspect circuit. Before any part gets swapped, you see a single parts-and-labor price. If we need to order a part, you'll hear the expected wait, and the return visit gets booked before we go.

Questions

Washer repair questions

Why is there still water in my washer drum after it stopped?

Usually a small item or packed lint is blocking the drain pump or filter, and sometimes the pump itself has failed. Until the water drains, the washer won't spin or unlock the door, so one fault looks like several.

Does hard water damage washing machines?

Rarely fatally, but it causes trouble at the edges: scale on inlet screens and dispenser jets slows the fill and leaves detergent behind, and it coats internal heaters. Checking the screens now and then helps.

How much detergent should I use if I have a water softener?

Less than you think. Start with the smallest dose the label allows and increase only if clothes aren't coming clean. Too much causes suds errors, extra rinses and musty smells.

Can a freeze damage a washer in the garage?

Yes. Water in the hoses, inlet valve and pump can freeze and crack them, and the leak appears on the next load. Before a hard freeze, close the faucets and disconnect the hoses if you can.

Is it worth fixing a washer with bad bearings?

It depends on age and model. Bearing jobs mean taking the tub apart, and some models sell bearings only with a new outer tub. On a newer washer it often makes sense; on an older one we'll lay out the trade-off.

What happens during a washer repair visit?

You get a three-hour arrival window. Our technician runs the washer through a cycle, tests the likely parts, and gives a single parts-and-labor price before starting. Once you say yes to the repair, the diagnostic fee is credited; parts are covered 90 days and labor 30.

Need your washer looked at?

Phone us at any hour, or send the online form and we ring back to set your three-hour window.

Call now, 24/7(210) 939-3313Book online