Jump to main content
Samsung · 6 min read

Samsung Error Codes: Washer, Dishwasher, Refrigerator and Dryer Meanings

A plain-language table of common Samsung codes such as 4C, 5E, UB, LC, 21E and OF OF, with the safe checks to try first, local causes like hard-water scale, and the codes that call for a technician.

By TrueHand Appliance Repair

A Samsung display can only fit two or three characters, so the codes are compact. Learn the pattern and most of them stop being mysterious. On washers and dishwashers, the number usually names the system: 3 for the motor, 4 for water supply, 5 for draining. The letter that follows mostly reflects the generation of the machine. Older models tend to show E, newer ones C, and some show a letter pair such as nF or nd instead. So 4E and 4C describe the same family of problem.

Codes still vary from model to model, and Samsung sometimes reuses a code for a different purpose on another product line. Treat the tables below as a guide, and confirm against the manual or Samsung's support site for your exact model number.

Step zero: a proper reset

A single power flicker during a spring thunderstorm, or a door opened mid-cycle, can throw a code that means nothing. Clear it properly:

  1. Switch the appliance off.
  2. Pull the plug or switch off its breaker and wait roughly five minutes.
  3. Restore power and run a short cycle.

A code that comes straight back is real. A code that never returns was probably a one-off.

Washer codes

CodeWhat it usually meansWhat you can safely try first
4C, 4E, nFNot enough water arrivingOpen both taps fully, straighten the hoses, clean the inlet screens
5C, 5E, ndWater not drainingClean the drain filter, check the drain hose and standpipe
UB, UE, UbUnbalanced loadRedistribute the load, level the washer
dC, dE, dSDoor not closing or lockingClear fabric from the door, close it firmly
LE, LCLeak in the base or a water-level sensing problemLook under the machine, cut back on detergent
Sd, SUdToo many sudsRun a rinse with no detergent, switch to measured HE detergent
3C, 3EMotor not turning as expectedRemove part of the load and retry
HC, HEWater heating faultNone beyond a reset; this needs service

Why fill and drain codes are so common here

San Antonio's water is hard. Most of that water comes from the limestone Edwards Aquifer, and its minerals settle on the little mesh screens where the hoses connect at the back of the washer. As those screens crust over, the fill slows until the washer gives up and posts 4C. To check them, close both taps, lay a towel down, disconnect the hoses from the machine and inspect the screens. Gentle brushing and a soak in white vinegar usually clears them. Don't pry the screens out with a screwdriver, because they tear easily.

Drain codes have a local twist too. Mineral grit mixes with lint and detergent in the pump filter and forms a sludge that slows the drain. Most front-load washers keep the filter behind a little door at the lower front. Put towels and a shallow pan in place first, because several cups of water are coming out.

Garage laundry rooms add one more cause. After a hard freeze, like the February 2021 storm, a split hose or a frozen line can produce 4C. If the hose is bulged or wet, replace it before you run the machine again.

Dishwasher codes

Samsung dishwasher codes shift more between models than washer codes do. These are the ones that turn up most:

CodeUsual meaningFirst check
4CWater supply problemSupply valve under the sink fully open, inlet hose not kinked
5CDrain problem on many modelsClean the tub-bottom filter, and look over the drain hose and disposal
LCLeak detected in the basePower off, look underneath, check for oversudsing
HEWater heating faultService call
OCOverfill, water level too highService call if it repeats

Hard water leaves a chalky film on the filter and spray arms that slows draining and cleaning. If your home has a softener, set the dishwasher's hardness setting to match, and use less detergent than you would on untreated water. Hand dish soap in a dishwasher will foam over and can set off LC.

Refrigerator codes

Many Samsung refrigerators show a number followed by E or C, sometimes only in a diagnostic mode.

CodeUsual meaning
21EFreezer fan fault
22EFresh-food fan fault
39E or 39CIce maker function fault
OF OFDemo or showroom mode; lights work but nothing cools

A fan code often means ice on the evaporator is stopping the fan blade, which points back to a defrost problem. A full manual defrost can clear it for a while, but if the code returns within days or weeks, a defrost part is usually failing. If your ice compartment is frosting over as well, our repair guides include a full walkthrough of Samsung ice compartments icing up. How you leave demo mode depends on the model, so use the button combination listed in your manual.

Dryer messages

  • A Filter Check light is only a reminder, not a fault. Clean the lint screen.
  • HE or HC on some models means the dryer is not heating as expected. On an electric dryer, that may be the heating element or a thermostat. On gas models it can be the igniter or gas valve.
  • Codes starting with t usually point to a temperature sensor.
  • Codes starting with d usually mean the door switch isn't reading closed.

If a dryer heats but needs two cycles, the vent is almost always restricted. That is a fire concern, not just an annoyance, so check the transition hose and the outside vent hood before you assume the dryer is at fault.

Same code, different model

Samsung builds many generations of each appliance, and the code tables shift between them. A top-load washer and a front-loader from the same year can use different codes for the same fault. Some refrigerators only show codes after a button combination puts them into a diagnostic mode, and some newer models send alerts to the SmartThings app instead of the display. If a code here doesn't match what you're seeing, search Samsung's support site using the full model number from the sticker, not just the brand and appliance type.

When it's a technician job

Stop troubleshooting and book a visit when:

  • The same code returns after a reset and the basic checks above.
  • There is water on the floor, or an LE or LC code keeps coming back.
  • You smell burning or hear grinding from the drum or pump.
  • Any heating fault shows on a gas dryer. Never take apart gas parts yourself.
  • A refrigerator code appears and the food is warming.

Copy the code down exactly, snap a photo, and note which stage the appliance was in: filling, washing, spinning or draining. That detail saves real time during diagnosis.

If the appliance is still under Samsung's factory warranty, contact Samsung first. Otherwise, we repair Samsung appliances across San Antonio. The technician diagnoses first and then quotes one price covering parts and labor, so you know where you stand before anything is taken apart. Start with our washer repair page or book online.

Keep reading

Call now, 24/7(210) 939-3313Book online