Jump to main content

Ice maker repair in San Antonio, fixed at your place.

Standalone ice machines work hard in a city where iced tea is a year-round habit. Here is what our technicians see in them, starting with the mineral scale that most San Antonio machines eventually fight.

Phones staffed 24/7Three-hour arrival window90-day parts warranty

Diagnosis
The failed part is found before any price
Approval
No work begins without your okay
Hours
Calls answered day and night
Warranty
Parts 90 days · labor 30 days

Book online

Send the basics. A dispatcher calls you back.

  1. 1Describe the problemYour ZIP code, the appliance, and the trouble it is giving you.
  2. 2Pick up when we callWe confirm the address and set a three-hour arrival window.
  3. 3Get one priceThe technician diagnoses it, then quotes parts and labor together. The diagnostic fee is credited if you go ahead.

Would rather explain it out loud? Call us any hour, any day.

Schedule a repair

Step 1 of 2 · Appliance and area

Step 1 of 2

Appliance and area

Which appliance?

Appliance

Where in the San Antonio area?

Booking costs nothing, and we never ask for a card.

Prefer to call? (210) 939-3313

1–2 hours
Typical time on site
30
Ice Maker faults we fix
9
Brands we service
24/7
Phones answered

Ice Maker problems

What is wrong with your ice maker?

Pick a symptom for the usual causes and the fix a technician makes.

  • Ice maker not making iceThe bin is empty and the machine is either silent or running without producing anything. A full stop usually comes down to water, freezing or harvest, and on hard-water machines scale can affect all three.

    Typical culprits

    • Shutoff valve closed, or a dead inlet valve
    • Freezing plate so crusted with scale that ice won't form properly
    • Clogged condenser keeping the system from getting cold
    • Hot-gas valve or harvest control never letting go of the ice
    • Bin sensor convinced the bin is already full

    How the technician handles it

    The technician confirms water supply and checks the inlet valve, then watches a full freeze and harvest cycle. Depending on where it stalls, we descale, clean the condenser, or replace the valve, sensor or harvest component.

  • Ice cubes coming out thin or hollowThe cubes look underbuilt: thin walls, hollow centers, or a dimple so deep the cube almost breaks. Either too little water is reaching the plate, or the machine is calling harvest before the cube has had time to grow.

    Typical culprits

    • Clogged filter or inlet screen cutting the water flow
    • Scale plugging holes in the water distribution tube
    • Thickness probe set thin or coated with minerals
    • Weak water pump
    • Sealed system short on refrigerant

    How the technician handles it

    To test flow we replace or bypass the filter, then scrub the inlet screen and the distribution tube and clean the ice thickness probe and set its gap. If water flow and sensor are right, the pump and refrigeration side are checked.

  • Water leaking from the ice makerWater pools under the machine or seeps into the cabinet beside it. Undercounter machines move a lot of water, and any slow drain or loose fitting shows up fast on a slab floor.

    Typical culprits

    • Drain line plugged or running uphill
    • Leaking inlet valve or supply fitting
    • Crack in the water trough
    • Water curtain knocked out of place on a cube machine
    • Drain pump failing on a machine below the drain

    How the technician handles it

    Close the valve feeding water to the ice machine. We check the pump and drain path, look over the inlet fitting and trough, and reseat the curtain. Leaks are fixed at the source, and the drain slope is corrected if needed.

  • Ice tasting or smelling offIce tastes stale, musty, metallic or like the freezer. Bad-tasting ice usually comes from what is growing in the machine or what is in the water.

    Typical culprits

    • Slime growing in the trough and bin
    • Water filter past its replacement date
    • Odors from food stored nearby
    • New plastic supply line giving off a taste
    • Sulfur or minerals in well water

    How the technician handles it

    Run the full clean and sanitize cycle with the cleaner the manufacturer names, install a fresh filter, and discard the first bin of ice it makes. If the taste persists, the technician checks for hidden growth and the water source.

  • Ice maker overflowing waterThe reservoir or trough overflows, water runs into the bin, or the machine sends water to the drain without stopping. Something is not ending the fill.

    Typical culprits

    • Inlet valve that won't close
    • Water level probe crusted with scale
    • Float hung up in the reservoir
    • Control board not shutting off the fill

    How the technician handles it

    Shut off the water supply. The technician cleans and tests the level probe or float, tests the inlet valve, and checks the control signal. Scaled probes are a frequent cause on SAWS water.

  • Ice machine making loud noiseGrinding, squealing, rattling or a constant drone louder than it used to be. Ice dropping into the bin is normal; mechanical noise is not.

    Typical culprits

    • Worn bearings in the condenser fan motor
    • Water pump bearing on its way out
    • Worn gearmotor turning the auger in a nugget unit
    • Loose panels buzzing
    • Machine out of level

    How the technician handles it

    We isolate the sound, replace a worn motor or pump, tighten panels and level the machine. On nugget units we check the cylinder for scale, since it loads the auger.

  • Ice machine not making enough iceIce comes out, just not enough to keep up. Summer heat lowers output on any machine, but a big drop beyond that points to something slowing the cycle.

    Typical culprits

    • Dusty condenser
    • Hot room or warm incoming water
    • Scale slowing each harvest
    • Refrigerant charge running low
    • Something blocking the front grille

    How the technician handles it

    The technician cleans the condenser, descales if needed, checks ventilation and measures cycle times. If cycles are still slow, the sealed system is tested.

  • Ice clumping together in the binCubes fuse into one large block. Ice in a bin slowly melts and refreezes, and when meltwater cannot drain, clumping speeds up.

    Typical culprits

    • Bin drain slow or plugged
    • Ice sitting in the bin for days without being used
    • Faulty bin thermostat or sensor
    • Drain line without enough fall

    How the technician handles it

    Empty the bin and use the ice regularly. If clumping continues, the technician clears the bin drain, corrects the slope and checks the bin sensor.

  • Cloudy ice from the ice makerCubes come out milky rather than clear. Clear ice depends on water flowing steadily so minerals and air wash away; anything that interrupts that leaves cloudy cubes.

    Typical culprits

    • Lots of dissolved minerals in the water
    • Scale on the freezing plate
    • Pump not moving enough water
    • Filter used up
    • Not enough water flushed out when each cycle finishes

    How the technician handles it

    Replace the filter and descale the machine. The technician checks pump flow and the purge setting, and may suggest a scale-reducing filter for hard water.

  • Ice maker drain pump not workingMachines installed below the drain line rely on a small pump to lift water out. Once that fails, water either pools back in the bin or escapes from the machine.

    Typical culprits

    • Burned-out pump motor
    • Debris over the pump inlet
    • Float switch hung up
    • Slime clogging the discharge line

    How the technician handles it

    We clear the discharge line and pump inlet, test the float and motor, and replace the pump if it has failed.

  • Ice machine condenser clogged with dustHeat taken out of the water is given off by the condenser. When it clogs, freezing slows, production drops and the compressor runs hot. Undercounter units pull air through the front, so they collect whatever is on the floor.

    Typical culprits

    • Floor dust and lint pulled through the front grille
    • Cooking grease from a nearby kitchen
    • Kick plate or rug covering the grille
    • Pet hair matted on the fins

    How the technician handles it

    Unplug the machine and brush or vacuum the condenser fins gently. Heavily packed or greasy condensers are cleaned by a technician, who also checks the fan.

  • Ice maker water inlet valve failedThe valve lets water into the machine. When it fails closed, nothing fills; when it leaks or sticks open, water keeps running. Hard water is tough on these valves.

    Typical culprits

    • Burned-out valve solenoid
    • Sediment packed into the valve screen
    • Worn diaphragm letting water drip through
    • Not enough water pressure at the valve

    How the technician handles it

    We check water pressure, clean the screen, test the coil and replace the valve if it is faulty.

  • Ice machine freezing into a solid blockInstead of releasing cubes, the plate is covered in one thick sheet of ice. The machine never moved from freeze into harvest.

    Typical culprits

    • Hot-gas valve that never opens
    • Thickness probe that never signals harvest
    • Water curtain stuck shut
    • Too little water flowing over the plate

    How the technician handles it

    Switch the ice machine off and allow the ice to thaw. Do not pry it loose. The technician cleans and tests the thickness sensor, tests the hot-gas valve and curtain switch, and checks water flow.

  • Ice machine dead with no lightsNo lights, no sounds. Start with the outlet and switch, because many undercounter and outdoor units sit on GFCI outlets.

    Typical culprits

    • Tripped GFCI or outlet
    • Power switch turned off
    • Blown fuse on the control board
    • Dead transformer

    How the technician handles it

    Reset the GFCI and breaker and check the power switch. If there is power, the technician tests the fuse, transformer and board.

  • Scale building up inside the ice machineWhite or tan crust forms on the plate, trough, tubes and probes. Hard water makes this normal here, but left alone it slows production and fools the sensors.

    Typical culprits

    • Hard SAWS or well water
    • Descaling skipped or overdue
    • Filter overdue for replacement
    • Purge set too low to flush minerals

    How the technician handles it

    Run the descale cycle with the manufacturer's cleaner. The technician can do a deeper clean, adjust the purge setting and recommend filtration.

  • Ice machine water pump not circulatingOn a cube machine the pump lifts water and spills it over the plate. If it stops, no ice forms, or only a thin film does.

    Typical culprits

    • Dead pump motor
    • Scale binding the impeller
    • Loose pump wiring
    • Clogged pump intake

    How the technician handles it

    The pump inlet and impeller are cleaned, the wiring is checked, and the pump is replaced if its motor has failed.

Show 14 more ice maker problems
  • Ice stuck on the plate and not droppingA full slab of cubes forms on the plate and just sits there. To release it, the machine is supposed to route hot refrigerant gas through the plate for a short time; when that step is skipped, the ice never lets go.

    Typical culprits

    • Burned-out hot-gas valve coil
    • Hot-gas valve stuck shut
    • Control never starting the harvest
    • Thickness probe not sending its signal

    How the technician handles it

    We test the hot-gas valve coil, check the control's harvest output and clean the thickness sensor. A failed coil or valve is replaced.

  • Ice machine control board problemThe machine behaves erratically, skips steps or does not respond. Boards here often fail after storm surges or moisture.

    Typical culprits

    • Surge from a storm or outage
    • Condensation getting into the electronics housing
    • Failed relay on the board
    • Sensor input that has gone bad

    How the technician handles it

    The technician tests the sensors and components first, then the board outputs. A bad control board gets swapped out, and then the dishwasher runs a full cycle so we can watch it work.

  • Ice machine showing an error codeA code or flashing light shows the machine has stopped itself. Codes usually flag a cycle that took too long or a missing signal.

    Typical culprits

    • Harvest taking longer than the board allows
    • Problem with the water fill
    • A sensor out of range
    • Freeze cycle running long because the condenser is dirty

    How the technician handles it

    Write down the code. We check what the code means on your specific model and test that circuit, because dirt and scale set off a lot of these codes.

  • Mold or slime in the ice machinePink, black or slimy buildup appears on the curtain, trough or bin. Warm, damp spaces breed it fast, and it gets into the ice.

    Typical culprits

    • Sanitizing skipped
    • Machine shut off with water left inside
    • Yeast in the air from brewing, baking or a busy bar
    • Warm, humid surroundings

    How the technician handles it

    Unplug, empty and run a full sanitize with the manufacturer's product. Heavy growth may need panels removed for a deeper clean by a technician.

  • Ice machine drain backing up into the binWater collects in the bottom of the bin and ice sits in it. The drain is clogged, poorly sloped or the pump has failed.

    Typical culprits

    • Slime blocking the drain
    • Drain line without enough slope
    • No air gap on the drain
    • Dead drain pump on a below-drain install

    How the technician handles it

    The technician clears and sanitizes the drain, corrects the slope or air gap, and tests the drain pump if one is fitted.

  • Ice maker bin overflowingIce spills out of the bin or jams the door. The bin is full but the machine doesn't detect it.

    Typical culprits

    • Dirty bin sensor
    • Failed bin thermostat
    • Board not reading the sensor correctly
    • Sensor bumped out of place

    How the technician handles it

    Clean the bin sensor and check its position. If the machine still overfills, the technician tests the sensor and control.

  • Ice machine compressor clicks but won't startYou hear a click and a hum, then nothing. The overload keeps cutting out the compressor before it can get started.

    Typical culprits

    • Bad start relay or capacitor
    • Overload cutting out
    • Low supply voltage
    • Compressor windings breaking down

    How the technician handles it

    The technician tests the relay, capacitor, overload and supply voltage, then measures the compressor windings. Start parts are replaced on the spot when they are the cause.

  • Ice machine water running nonstopWater keeps flowing to the drain even when the machine should be freezing. It wastes water and can stop production.

    Typical culprits

    • Fill valve that won't shut
    • Purge or dump valve hanging open
    • Faulty level probe
    • Board never signaling the end of the fill

    How the technician handles it

    We test and clean the inlet and purge valves, clean the level probe and check the control signal. Scaled valves are replaced.

  • Ice stuck in the ice maker moldOn machines with a mold and ejector, cubes stay frozen in place and the ejector stalls. The mold is supposed to warm slightly to release them.

    Typical culprits

    • Dead mold heater
    • Ejector motor burned out
    • Faulty mold thermostat
    • Stripped ejector gear

    How the technician handles it

    The mold heater, thermostat and motor are tested, and the bad part or the full ice maker assembly is replaced.

  • Nugget ice maker not making iceNugget ice comes from a chilled cylinder, with an auger turning inside to scrape off the ice as it forms. If the auger stops or the cylinder is scaled, production slows or stops.

    Typical culprits

    • Failed auger gearmotor
    • Minerals coating the freezing cylinder
    • Water supply problem
    • Worn auger bearing

    How the technician handles it

    We check water supply, descale the cylinder and test the gearmotor and bearings. Worn parts are replaced.

  • Portable countertop ice maker stopped workingCountertop units fill from a reservoir and are simpler than built-in machines. They stop when the pump, sensor or fan fails.

    Typical culprits

    • Dead water pump
    • Dirty ice-full sensor
    • Fan not running
    • Drain cap on the reservoir not screwed tight

    How the technician handles it

    Clean the sensor and check the drain plug. If it still fails, the technician can test the pump and fan, though on inexpensive units replacement often makes more sense.

  • Undercounter ice maker overheatingThe machine runs hot, production drops and it may shut down. Undercounter units breathe through the front, so blocking the grille starves them of air.

    Typical culprits

    • Something blocking the front grille
    • Installed in a cramped space
    • Dusty condenser
    • Built in without the airflow gap it needs

    How the technician handles it

    Clear the front grille and clean the condenser. The technician checks the installation clearances and the fan, and suggests changes if the cabinet is trapping heat.

  • Ice machine condenser fan stoppedThe fan that cools the condenser has stopped, so the machine overheats and production falls or stops.

    Typical culprits

    • Burned-out fan motor
    • Something caught in the fan blade
    • Broken or loose wire to the fan
    • Seized fan bearings

    How the technician handles it

    The technician checks that the blade turns, tests the motor and wiring and replaces the motor if needed. The condenser is cleaned at the same time.

  • Ice cubes uneven sizesSome cubes are full, others thin or partial. Water is not spreading evenly across the plate.

    Typical culprits

    • Distribution tube partly plugged
    • Machine sitting out of level
    • Mineral crust on parts of the freezing plate
    • Pump moving too little water

    How the technician handles it

    Level the machine. The technician cleans the distribution tube, descales the plate and checks pump flow.

Brands

Ice Maker brands we repair

All brands →
  • Sub-Zero logo
  • Atosa logo
  • Hoshizaki logo
  • Ice-O-Matic logo
  • Manitowoc logo
  • Maxx Ice logo
  • Perlick logo
  • Scotsman logo
  • U-Line logo

From our technicians

Ice Maker repair notes for San Antonio homes

If you own an undercounter ice machine in San Antonio, sooner or later you will meet scale. The Edwards Aquifer is limestone, and the water that comes out of it carries calcium and magnesium that settle on whatever surface the water touches longest. In an ice machine, that is the freezing plate, the water distribution tube, the sensors and the valves.

That is why so many ice-maker calls here start with a complaint about ice, not about the machine. The cubes are small, thin, cloudy or stuck together. The machine is still running. It is just running through a layer of mineral that keeps it from doing its job well.

This page covers standalone machines: home undercounter units, nugget ice makers, outdoor kitchen units and the light-commercial machines in offices, salons and small restaurants. For an ice maker built into a refrigerator, see our refrigerator page instead.

Scale: the San Antonio ice machine problem

On a cube machine, water flows over a cold metal plate and freezes in layers. When scale coats that plate, the ice sticks harder and releases slower, so harvest takes longer and cubes come out uneven. Scale on the distribution tube blocks some holes, so part of the plate gets less water. Scale on the thickness probe or water level probe makes the control misread what is happening, and the machine either harvests too early or freezes into a solid slab.

Nugget machines fight it in a different place. An auger shaves off the ice that forms on the inner wall of a chilled cylinder. Scale on that cylinder makes the auger work harder, which wears the gearmotor and bearings. A noisy nugget machine is often a scaled one.

Descaling frequency depends on your water and on whether a softener or filter sits in the line. Some homes need it every few months, others once a year. If your machine has a descale light, believe it.

How a technician works through a no-ice call

First, is water getting in? We check the supply valve, the filter and the inlet valve screen, which is a common catch point for sediment and scale. Then we watch a cycle. Does the pump circulate water over the plate? Does the plate get cold? Does the machine try to harvest, and does the ice release? Each step narrows it down.

If water and freezing look right but nothing drops, the hot-gas valve or the harvest signal is the usual suspect. When the plate isn't getting cold, we check the condenser, its fan and the compressor start parts before we touch the sealed system. When the bin is full and the machine keeps making ice, or it never starts because it believes the bin is full, we look at the bin sensor or thermostat.

Heat, drains and where the machine lives

Undercounter units breathe through the front grille. Push a trash can or rug against it, or tuck the machine into a cabinet that was never designed with airflow in mind, and it will overheat. Outdoor kitchen machines face a hotter version of the same problem: a San Antonio patio in July can keep a machine running constantly and still leave the bin half full. Ice production drops as room and water temperature rise, and that is physics, not a fault.

Drains matter more than most people expect. A gravity drain needs a steady slope and an air gap; a machine installed below the drain needs a drain pump. Slime and scale clog both. With the drain backed up, water stands in the bin, the ice thaws and fuses into lumps, and odors can develop. During hard freezes, outdoor units and supply lines on exterior walls can split, so shut off and drain an outdoor machine before a freeze if the manual allows it.

Cleaning safely, and what softened water changes

Clean and sanitize with the products the manufacturer calls for, and use the machine's built-in clean cycle as directed. Unplug before you reach inside or remove panels. Throw away the first batch of ice after any cleaning. Unless your manual says bleach or vinegar is safe for that machine, don't use them; the wrong chemical can harm the sensors or the plate coating.

A softener or a scale-inhibiting filter can cut scale dramatically, but some machines rely on minerals in the water for their level or conductivity sensors. Check the manual before running fully softened water to a machine. Hill Country homes on wells may also see sulfur taste or sediment, which a proper filter helps with. Change the filter on schedule; an exhausted one is as bad as none.

Repair or replace, and what our visit includes

Valves, pumps, sensors, fans and boards are all routine repairs, and a good descaling can bring a struggling machine back to full output. A failed compressor on an older residential machine is where we will talk honestly about replacement. Light-commercial machines are usually worth repairing longer.

On visit day, expect the technician within a three-hour window. You'll hear what broke and get one quoted price covering parts and labor before work begins, with your diagnostic fee applied to it. When a part is not on the truck, you learn how long it will take, and the follow-up visit goes on the calendar before we leave.

Questions

Ice Maker repair questions

How often should I descale my ice machine in San Antonio?

It depends on your water and filtration. Many homes on SAWS water without a softener need it every few months; homes with a softener or a scale-reducing filter can often go longer. Follow the machine's indicator if it has one, and descale sooner if cubes get thin or cloudy.

Why is my ice cloudy?

Cloudy ice usually means minerals or air trapped in the cube. Hard water, scale on the plate, a weak water pump or a filter that is past its life all contribute. Cleaning and a fresh filter often improve it.

My undercounter ice maker is making less ice in summer. Is it broken?

Some drop is normal because production falls as room and water temperatures rise. A large drop usually means the condenser is dirty, the front grille is blocked or scale is slowing the harvest. Clean the grille area and call if output stays low.

Can I use softened water in my ice machine?

Often yes, but check the manual. Some machines use water conductivity to sense level, and very soft water can confuse them. A scale-inhibiting filter is another option.

Do you repair commercial ice machines?

We service light-commercial ice machines such as the ones in offices, salons, small restaurants and bars, at your location. If your setup is big enough to call for a commercial refrigeration contractor, we'll say so.

Is it safe to clean my ice machine myself?

Routine cleaning with the manufacturer's cleaner and the built-in clean cycle is fine. Unplug before reaching inside, never use sharp tools on the plate or cylinder, and leave anything involving refrigerant, wiring or the compressor to a technician.

Need your ice maker looked at?

Phone us at any hour, or send the online form and we ring back to set your three-hour window.

Call now, 24/7(210) 939-3313Book online