Picture the path the air takes in a lot of San Antonio houses. The laundry sits in an interior closet or off the garage, nowhere near an outside wall. So the exhaust goes up: out the back of the dryer, through a short hose, into a duct in the wall, across the attic and out a cap on the roof. That run can be long, it often has several bends, and in July it crosses an attic that gets far hotter than the outdoor air.
Long, hot, hard-to-see runs are where lint settles. Lint is light, dry and burns readily, and a dryer is a heat source sitting at the start of the duct. That's the whole reason a vent check matters. The good news is that most of what you need to look at takes less than half an hour, and a few items are better left to a vent cleaning professional.
Is your vent already restricted?
Think about how the dryer has behaved lately. Any of these suggests the air isn't getting out:
- A normal load now needs a second cycle.
- The dryer's top or side panels get unusually hot.
- The clothes are very hot when they come out, yet the seams are still damp.
- The laundry room turns warm and muggy while the dryer runs.
- You notice a hot or scorched smell.
- Lint piles up behind the machine on the floor, or around the door.
- A Check Vent light, or an airflow code on brands that have one, keeps appearing.
Start at the lint screen
Clean the screen before every load. Every few months, scrub it with a soft brush in warm, soapy water. Even with a spotless-looking screen, dryer sheets can coat it with a waxy film that blocks air. To test, hold it under the tap. If water beads on the mesh instead of running through, it needs a scrub. While the screen is out, shine a light into the slot. Lint often packs in below it, and a long, narrow vacuum attachment or a flexible lint brush will reach it.
The transition hose behind the dryer
This is the short flexible connector between the dryer and the wall duct, and it's the most common problem spot we find.
With an electric dryer, pull the plug before you slide it out. With a gas dryer, slide it forward only as far as the gas connector allows without strain. If reaching the hose means pulling a gas dryer far out from the wall, let a technician handle this step.
| What you find | Why it matters | Fix |
|---|
| White vinyl or plastic hose | Not suitable for dryer exhaust and a fire risk | Replace with a metal transition duct |
| Thin foil accordion hose, crushed or kinked | Flattened sections trap lint and choke airflow | Replace with semi-rigid metal, and leave space behind the dryer |
| Joints held with screws | Screw tips poke into the airflow and snag lint | Use clamps or foil tape rated for ducts |
| Far more hose than needed | Extra length sags and collects lint | Trim to the shortest practical run |
Crushed foil is especially common in closet laundries, where the dryer gets shoved back against the wall to close the doors. Check your dryer's installation guide for the recommended transition material and clearance.
The long run through the attic
Every manufacturer lists a maximum vent length in the installation manual, and each elbow counts against it. Local building codes set limits too. Plenty of attic runs meet or exceed those limits, which is why they clog sooner and need cleaning more often than a short run out an exterior wall.
What to look for, if you can safely get into the attic:
- Sections that have come apart at a joint, venting lint and humid air straight into the attic.
- Flexible duct sagging between rafters, which lets lint pile up in the low spots.
- Crushed duct where something heavy was stored on top of it.
- Moisture stains or rust on the duct, which suggests condensation in cooler months.
Attics here can be dangerously hot in summer. Go up early in the morning, carry water, step only on framing and don't stay long. Cleaning a long attic run properly takes the right rotary brush equipment and often access from both ends. That's a job for a dryer vent cleaning professional.
The roof cap or wall hood
With the dryer running on heat, check the outlet. At a wall hood, the air coming out should be strong and warm, and the flap should swing open freely. A roof cap is harder to judge from the ground, and you should not climb onto the roof to check it. A pitched roof in the Texas sun is a real fall hazard. Watch from the yard instead for lint fuzz around the cap, or have a vent professional inspect it.
Common problems at the outlet:
- Bird nests. Birds love dryer vents and roof caps, especially in spring. A nest can block a vent almost completely. Removal and a proper bird guard belong to a professional, particularly on a roof.
- A screen over the outlet. Fine screens catch lint and clog quickly, and many codes don't allow them on dryer exhausts. Use a vent guard made for dryers.
- A stuck flap. When the damper won't open, lint and moisture stay trapped in the duct.
- Plants or debris crowding a wall hood. Keep the area around it clear.
Inside the dryer cabinet
Lint also collects inside the dryer around the drum, the heater or burner and the blower. Getting to it means removing panels that expose wiring, sharp edges and, on gas models, the burner and valve. That's a job for a technician, and if your dryer is several years old, it's worth requesting during a repair visit.
Gas dryers and carbon monoxide
On a gas dryer, the exhaust from the burner leaves through that same vent. If the vent is blocked, those gases can back up into the house. Keep carbon monoxide alarms working, never let a gas dryer exhaust indoors, and if you smell gas, walk out without touching any switches, then phone CPS Energy or the gas company from outside.
A simple schedule
- Lint screen: every load.
- Wash the screen: every few months.
- Transition hose and outlet check: twice a year.
- Professional duct cleaning: at least once a year for attic and roof runs, and more often for big households or pets.
When the dryer needs repair
Call a technician if the dryer heats but won't dry even after the vent is cleared, stops heating altogether, keeps blowing its thermal fuse, or smells of burning. A blown thermal fuse usually points to overheating from a restricted vent, so clear the vent first, or the replacement fuse will blow as well. Our dryer repair page covers gas and electric models, and a no-heat or burning-smell problem can go through our emergency appliance repair line. You can also book online.